Current needed to r...
 
Notifications
Clear all

Current needed to run e682 and just data?

10 Posts
6 Users
0 Reactions
2,602 Views
Posts: 2048
Topic starter
(@scootchu)
Noble Member
Joined: 17 years ago
[#36011]

I am contemplating running my 682 to sets of GECE's with there own wall wart power packs, sending just a data line and ground to each from the 682.

I am assuming I won't need much for powering the 682 and the data to each string. Does anyone have an idea of what kind of amperage I would need for a power supply?


9 Replies
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I believe that is in the E682 manual.


Reply
Posts: 2048
Topic starter
(@scootchu)
Noble Member
Joined: 17 years ago

Power:
There are two connections for pixel power, allowing the use of
two separate pixel power supplies. This also allows a mix
of 5 volt and 12 volt pixels (for example) to be controlled
by a single E682. Each power inlet supplies power to 8 pixel
outputs and is rated to carry up to 32 amps. The E682 itself
is typically powered from the right-hand (output groups 3 and
4) pixel power supply, but may also be powered independently by
a power supply that is capa
ble of providing 7-24 volts
DC at about 500ma, connected to J19.

So 7-24v at 500ma? I can live with that.


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago

Yeah, that looks right. I bet the end-number is MUCH lower than that too (though I've never measured it); I bet Jim gave himself plenty of headway when he wrote that into the manual.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

That's the one. J19 will I remember that this fall when someone else asks?


Reply
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

From the E682 manual: The E682 is most commonly powered from the same power supply that operates the pixels, but may be powered by a small dedicated power supply (7-24VDC at 300ma) if desired.

What is your GECE configuration going to look like?


Reply
Posts: 2048
Topic starter
(@scootchu)
Noble Member
Joined: 17 years ago
Xenia wrote:From the E682 manual: The E682 is most commonly powered from the same power supply that operates the pixels, but may be powered by a small dedicated power supply (7-24VDC at 300ma) if desired.

What is your GECE configuration going to look like?

Most likely if I do my windows or my bushes with GECEs I'll use the GE 5volt Wall Wart PS's on each string of 25 to 50 pixels and run 2 wires to each string from the controller (data & grd) I have so many of the power supplies that it makes sense.

Will Cat 5 work for the data and ground?


Reply
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

I had the same set up this year (using stock gece 5v ps) and it worked just fine thought I use 18ga wire. I got runs of 30 ft from the controller With no problems. Just seemed like such a waste to not use them and it was really only one more wire, I made and extension cord with inline females for all the power supplies to plug in to


Reply
Posts: 179
(@mildog)
Estimable Member
Joined: 12 years ago

When you use this method I have read you have to combine the grounds. Is this correct?


Reply
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

Yes you need to tie the grounds from both power supplies together


Reply
Share: