Anyone have a reflo...
 
Notifications
Clear all

Anyone have a reflow setup?

9 Posts
5 Users
0 Reactions
4,543 Views
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago
[#36751]

This is off topic, but I figured this is the best board to ask the question. I have a Multiwii Flight Controller and one of my resistors was either not seated right from the get go or I put a little too much heat to the pin header when I soldered it. I'd be more than happy to pay someone for their time if you think you can slide it back onto the pads and get it tacked back on.... look at the top left of the photo beside the right pin. https://drive.google.com/file/d/0Bxq_KcnUwwu3dFVLMzV1SndOZEE/view?usp=sharing


8 Replies
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

Hot air its probably your best bet for that type of repair. If you dont find anyone close to you i think its liek $2 for a usps shipping, ether way if its under a few oz.

My only concern is that looks almost sheared off not melted the track may have gone with it. Anyway shoot me pm for my address I can fix it for you. I have fixed far worse:)


Reply
Posts: 3650
(@jhinkle)
Famed Member
Joined: 15 years ago

Hot air is best but you should be able to fix that with a small tip iron.

Touch both sides 1/4 second each side until both sides flow -- then either remove the device, clean up the surface and resolder -- or just solder after you reposition it.

Joe


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago
JHinkle wrote:Hot air is best but you should be able to fix that with a small tip iron.

Touch both sides 1/4 second each side until both sides flow -- then either remove the device, clean up the surface and resolder -- or just solder after you reposition it.

Joe

As well as a good light and magnifier. And possible a flux pen.


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

If I had some better light, magnification and tweezers...I think I could pull it off...but I'm not trying without that stuff...lol


Reply
Posts: 459
(@shockwave)
Reputable Member
Joined: 15 years ago

I do. Quartz heating elements on the top AND the bottom - about 1200W

I have had mixxed results with hot air - when you get to parts like 0603 and smaller, stuff easily gets blown around. And I believe most Assembly houses use IR, like my modified toaster oven. So that's what I use.

You can get an oven controller from Sparkfun and a 75$ dual element minioven from Sears, and be good to go.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
Shockwave wrote:I do. Quartz heating elements on the top AND the bottom - about 1200W

I have had mixxed results with hot air - when you get to parts like 0603 and smaller, stuff easily gets blown around. And I believe most Assembly houses use IR, like my modified toaster oven. So that's what I use.

You can get an oven controller from Sparkfun and a 75$ dual element minioven from Sears, and be good to go.

I have the SparkFun controller and a B&D dual element oven - works great for me and in all about $100 invested... I also have a hot air station I got on eBay for about $50. Both have their place...


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

It will be on its way back in the morning:) after youtube takes it sweet time processing...


Reply
MindTrik
Posts: 1542
Topic starter
(@mindtrik)
Noble Member
Joined: 16 years ago

AWESOME man! Thanks for fixing that! I'm not worried about a little melted plastic.


Reply
Share: