Notifications
Clear all

WS2812B vs 2811

22 Posts
14 Users
0 Reactions
10.9 K Views
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
[#36754]

Hello All,

Can anyone tell me what the difference is between these 2 pixel types WS2812 and a WS2811?

Thanks.

SC


21 Replies
Posts: 1049
(@phrog30)
Noble Member
Joined: 12 years ago

There's a difference of 1.


Reply
Posts: 122
(@robertc)
Estimable Member
Joined: 14 years ago

The WS2812 is an RGB LED, with a WS2811 control IC, built right into the LED.

The WS2811, does not have the control IC built into the RGB LED.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
robertc wrote:The WS2812 is an RGB LED, with a WS2811 control IC, built right into the LED.

The WS2811, does not have the control IC built into the RGB LED.

Thanks.....wonder what advantages one would give you over the other...


Reply
Posts: 15
(@dgtlpro)
Active Member
Joined: 14 years ago

The 2812 allows tighter grouping therefore more pixels per meter.

Sent from my XT1254 using Tapatalk


Reply
Posts: 130
(@charleskerr)
Estimable Member
Joined: 16 years ago

The obvious advantage is if you want a 5050 type led, the WS2812 allows more compact designs. The WS2811 is just the chip, so it allows one to connect to a variety of LED form factors, or even non led applications that need a PWM that the WS2811 puts out. The WS2812 also requires less pin usage in ones design.

One item, the WS2812 (or at least the ones I have used) have the RG channels switched from the WS2811.


Reply
RobG
Posts: 1255
 RobG
(@robg)
Noble Member
Joined: 14 years ago

As charleskerr pointed it out, WS2811 is an IC and can be used with any LED, like 8mm, where with WS2812 you are limited to 5050.
There are 2 types of WS28212, 2812 and 2812B. The B version suppose to be brighter, draws more current, uses 4 pin package vs 6 pin, and has slightly different timing.
At some point, WS was also making WS2812D, which was WS2811 in 8mm package. That one is now discontinued, but you can get similar one from another manufacturer (APA-106)


Reply
Posts: 255
(@rogerh)
Reputable Member
Joined: 12 years ago

One of the more important differences in the WS2812B is it has reverse voltage protection. If you wire up a string and mix up the plus and minus, all that will happen is they won't light up. With the WS2811 and WS2812's you might fry the whole string.


Reply
Posts: 366
(@technician)
Reputable Member
Joined: 12 years ago

I'm surprised nobody has mentioned this yet.
The 281212 is unified and can have only 1 LED per pixel and is only 5V.
The 2811 can run series strings of LEDs per IC (pixel), so the popular bright 2 LED pixels are NOT 2812. For long strings where multiple LED's per chip is OK, it can reduce the channel count required, such as for leaping arches, multi LED square pixels, and related LED boards. 3 LED's per chip is popular in 12 Volt strings. It makes efficient use of the higher voltage.
One reel of LED's I bought last year at Costco has 6 LED's for each IC. At 30 LED's per meter, each meter is only 5 pixels long. My reel is only 27 IC's long with 162 LED's. It is a convenient 12 Volt string and much more useful for cove lights, leaping arches, and other larger wash applications.


Reply
Posts: 15
(@daisy1988)
Eminent Member
Joined: 11 years ago

ws2811 one ic control three led,ws2812b ic built-in led can be control individually.


Reply
Page 1 / 3
Share: