Highest density Meg...
 
Notifications
Clear all

Highest density Mega Tree anyone has built?

13 Posts
9 Users
0 Reactions
13 K Views
Posts: 2
Topic starter
(@paulb)
New Member
Joined: 8 years ago
[#50133]

This year, our tree was 25-ft tall with 96 strands of 100 pixels this year (360-degree). It is working reasonably well with images and video. I realize that many trees are intended to just do patterns/effects.

I'm curious as to any higher pixel-count trees that anyone has constructed & how they dealt with power issues.

At 60 watts per strand of 100, we are at 5,760 watts on the occasions when all pixels are on full. That's 480 amps of 12v or about 50 amps of 120 volt. We ended up running a separate 100 amp service just for the tree & surrounding items.

Currently, I have 3 Falcon V3 controllers with 1 expansion cards each & a total of 6 x 100-amp 12v (1200 watt) power supplies. We had a heat problem last year that we mitigated with larger & power-vented enclosures.

Any advice from the trenches?


12 Replies
StickyWicket
Posts: 548
(@stickywicket)
Honorable Member
Joined: 14 years ago

Ya one “Get a smaller tree!”

And here I was impressed with my 120 pixel x 35 strip 180 tree.

That’s a lot of everything! 🙂


Reply
Posts: 215
(@reelpilot)
Reputable Member
Joined: 12 years ago
PaulB wrote:This year, our tree was 25-ft tall with 96 strands of 100 pixels this year (360-degree). At 60 watts per strand of 100, we are at 5,760 watts on the occasions when all pixels are on full. That's 480 amps of 12v or about 50 amps of 120 volt. We ended up running a separate 100 amp service just for the tree & surrounding items.

Are you actually measuring your power loads or are you just basing off of general assumptions at 100%? There are definitely two schools of thought out there. Some will say build everything for 100% brightness on full white and others will say to build to how bright you are actually going to run your show. I think more people, myself included, build to the actual power consumption at a much lower brightness.

With the exception of floods and arches, where the light is diffused inside of the tubing, the brightest I run my show is 30%. Items such as my mega tree and other dense props like my snowflake tower I run at 20%. Power consumption is just a fraction at that brightness compared to 100%. Pictures and videos look a whole lot better too at low brightness levels.

The only way to know specifically how much power you are drawing is to test. If you don't have one already I recommend buying a Kill A Watt so you can see exactly what you drawing on the AC side and multimeter that will measure DC amperage draw. For example my mega tree has a little more than half the pixels of your tree. It's 48 strings of 107 pixels plus another 106 for the star, 5242 pixels in all. At 20% brightness and full white I can safely power this with 3 350 watt power supplies, still have 20% margin on power supply output and it only draws 7.5 amps on the AC outlet. When actually running a sequence and not holding full white the nominal AC amperage draw is less than 4 amps.


Reply
Posts: 486
(@uncledan)
Honorable Member
Joined: 11 years ago

I'm assuming your tree was 3" spacing? The first step would be closer spacing on nodes if you want images or video. My 270 tree is 48x110 with 2" spacing using a Falcon F16v3 with two expansions. 48 ports with one string per port powered through the boards (no injection). The tree is powered from a single Meanwell RSP3000-12 power supply. At 40% intensity white the tree is 105 amps or .020a per node. While the show is running the power supply is generally loaded 30% or less. You can run these power supplies in parallel as well. I have three others in parallel for 600a at 12v. Compact and reliable when you need a lot of power in a centralized location


Reply
mikel3332
Posts: 153
(@mikel3332)
Estimable Member
Joined: 16 years ago

I am still baffled every time I see power calculations. Your saying 60 watts per strand of 100, I have measured mine at 100% brightness , full white 12v at 37.2 watts per 200 string. So are you going by calculated wattage or actual measurements? Or am I missing something here?


Reply
Page 1 / 3
Share: