How do I remove 8 f...
 
Notifications
Clear all

How do I remove 8 function controller from light string?

61 Posts
19 Users
0 Reactions
51.8 K Views
toodle_pipsky
Posts: 1285
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Re: How do I remove 8 function controller from LED string?

From my understanding - and so far it's worked for me, but that's no guarantee 😀 - you remove the controller based on the same principal as removing it from a incandescent set. So there will be each of your channels and 1 neutral/power/common, whatever you want to call it.

As MPH has said, the difference is that you will need a resistor for each string of LEDs and that will go on each of the "channels" you removed. Another tricky thing you'll have to take note of is each coloured LED will be slightly different so you'll end up needing different resistors for each channel. I used this site http://led.linear1.org/led.wiz to calculate the resistor I needed. Another note is that they'll be 1 watt resistors, they're a bit bigger (in size) than the ones we normally use for boards. Those 16 light strings you're talking about are 4 channels of 4 LEDS each (4 different colours) so you'll need to do a seperate calculation for each. Just use the standard measurements the calculator gives you for each colour as they're not special LEDs.

As a little tip - I took apart one of these sets to just see what was going on and how it was wired up. I found that ultra helpful to understand how it all worked, but you may not want to do that if you've only got a limited amount of lights.

One thing I’m unsure of is that I have 1 set of static LED lights that had a bridge rectifier on it (I believe that’s 4 diodes in like a diamond configuration and something about it changes AC to DC??) and this set doesn’t. Like the resistors, I think it might be “hidden” in the controller – there are certainly 4 diodes on the controller, but they’re not in that diamond configuration. Being the total noob I am, maybe someone with more knowledge can say if the modified LEDs need a rectifier on it as well?


Reply
TimW
Posts: 554
 TimW
(@timw)
Honorable Member
Joined: 19 years ago

Re: How do I remove 8 function controller from LED string?

Hi Terry

These controllers are usually 2 or 4 channels. I think this one is a 4 chanel (so there will be 2 wires coming in and 5 wires going out. (But I can't quite see either)

On the conventional controllers I've pulled to bits the transistor looking things are SCRs - the power fed to the lights is full wave rectified but with no filtering so the voltage drops enough to turn the SCR off a couple of times/cycle .
(I'm hoping that capacitor at the bottom is there as backup power to the chip when its not powered so it remembers its setting)

Those 4 resistors in a row - they don't usually appear on the boards I've seen for non - led lights - I'd look to see if they are the series resistors mrpackethead is referring to. They will be in series with 4 of the five wires going out. The other end of the resistors will end up on one of the 4 scr's.

The thing I find interesting with these controllers is that they actually send (unfiltered) DC to the lights. Obviously DC is necessary for LED strings.. but they seem to do it with the minis as well. I guess its a cheaper way to do it?

Are you planning to put a ssroz on the 24V to control them? If that's the plan then I guess all we need to figure out is to how to bypass the controller chip and make sure the 4 SCRs stay on all the time that power is on to the controller.. changing a couple of tracks ought to do it.

That's probably the easist way.. you can use the power supply you already have and the resistors already there will do the trick.

As already mentioned - can we have some clearer pictures on the front and back of the board?

Tim


Reply
TimW
Posts: 554
 TimW
(@timw)
Honorable Member
Joined: 19 years ago

Re: How do I remove 8 function controller from LED string?

And... as tp pointed out you might need a different resistor per led colour. Looking at the pic all the resistors are the same value (as far as I can tell)... looking at the packaging in the pic ... its looks like only one colour of leds being used? AHA!

Do you want each of the channels to switch all together or 4 separate channels?


Reply
piesrule58
Posts: 443
Topic starter
(@piesrule58)
Honorable Member
Joined: 19 years ago

Re: How do I remove 8 function controller from LED string?

Thanks Guys

I have attached 2 more pictures (I hope they help)
I hope to run these off a Grinch and SSROZ.
They are only one colour (clear)
I would like all 16 LED's to turn off and on together.
Wall Wart that came with them is 24v AC 150mA 3.6VA.
I would prefer to modify board if possible.
My electrical knowledge is ZERO so simpler the better.

Thanks again, Terry

led's2 001
led's2 008

Reply
prof
Posts: 266
 prof
(@prof)
Reputable Member
Joined: 19 years ago

Re: How do I remove 8 function controller from LED string?

Terry,

Do you want to trash to board or be able to reinstate it as a controller later on. It would also be easier if you used 1 set of lights per oz ssr board that way you could re usethe plugpack.

Craig.


Reply
Page 3 / 13
Share: