2 channel learning ...
 
Notifications
Clear all

2 channel learning prop controller

76 Posts
24 Users
0 Reactions
34.4 K Views
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago
[#20695]

I have been working on a Halloween prop controller and so far things look very good. It is still in prototyping stages but the I believe concept is solid enough to share with the community. This controller uses a PIC12f683 micro controller, 3 push button switches, 2 relays and a few other parts. Cost to build will be around $6. Basically how it works is you push a record button then tap in the timing sequence you want the 2 channels to come on and off. Record time is 102 seconds and the sequence is saved to the EEPROM so it will remain stored even after power is unhooked from the board. Here is a video of my prototype in action.


75 Replies
mikeh65
Posts: 794
(@mikeh65)
Prominent Member
Joined: 19 years ago

I hope this is inexpensive to build. I have worked for a haunted house for many years and we have several devices like this. They are called the Maestro II
http://www.halloweenfxprops.com/animation-maestro-ii , they work just like you show but can handle any voltage put through their build in relays. As you can see from the link, they are not cheap. This may be a much cheaper solution. Keep going!


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago

The relays I have on order but are currently untested are good for 120v@10 amp. Max current draw will be limited by the PCB but I think we should be able to get somewhere near 5 amps each channel. The cost of the circuit shown in the video was under $3. by the time we add in relays and voltage regulator it should be up to around $6. The PIR used in the video will set you back about $3. Of course this one is DIY so you have to put it all together yourself. Even if you have to buy a soldering station and PICkit2 I believe you would still be money ahead on the 1st one compare to the out of the box solution.


Reply
BuzzKill
Posts: 577
(@buzzkill)
Honorable Member
Joined: 19 years ago

How soon can you have PCB's printed? 🙂


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago
BuzzKill wrote:How soon can you have PCB's printed? 🙂

My plans at this point are home etch only. Hope to have etch files and firmware available within a week or two.

tyler


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago

That's cool,,, I like it...


Reply
lightman
Posts: 1524
(@lightman)
Noble Member
Joined: 19 years ago

Great idea. Wish I had this 20 years ago when I was heavy into Halloween shows.

Nice job....

Lightman


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Clever!


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago

Just a quick update. I did all the parts I need to complete this board have been shipped and I expect to have one built and tested by the end of this week or early next week. The board layout is near complete. I'm trying to make this a 100% Tayda Electronics build to keep price low. Some of the part numbers Tayda gives are not listed as components in Eagle so I tried to look at the datasheets provided and choose similar footprint parts. As soon as I get all the needed parts I will build one to make sure that everything fits and works as it should. I have attached a PDF of the board layout. As always question, comments, and criticisms are welcome.

Tyler


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

Nice project. 🙂


Reply
Page 1 / 8
Share: