2 channel learning ...
 
Notifications
Clear all

2 channel learning prop controller

76 Posts
24 Users
0 Reactions
34.4 K Views
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Is the silk for the G5LE on the right correct? Seems odd for the pinout to be different.


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

Oh, I meant to ask; did you use all of the bits in each EE byte for channel data?


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago
Jrd wrote:Is the silk for the G5LE on the right correct? Seems odd for the pinout to be different.

The silk screen likely has several errors at this point. My main concern at this point on the board layout is the copper layer. I will go back and clean up the silkscreen after I test the board. Make it work first then make it look good is my way of thinking.

David_AVD wrote:Oh, I meant to ask; did you use all of the bits in each EE byte for channel data?

Yes, Four events are stored per byte of EEPROM. A bit 1 is channel on a bit of 0 is channel off. Event 1 is stored in bits 7 and 6 event 2 is stored in bits 5 and 4. Event 3 is stored in bits 3 and 2. Event 4 is stored in bits 1 and 0. By using this method I can store 1024 total events in only 256 bytes of ram. Each event period last 100 ms for a total of 102.4 seconds of record time.


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

Ah, that's what I thought. I made something similar a while back, but that used one byte per step as it had 8 channels.

For the relays, you could get better mains to ELV clearance by choosing relays that don't have the common between the coil terminals.


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago
tstraub wrote:The silk screen likely has several errors at this point. My main concern at this point on the board layout is the copper layer. I will go back and clean up the silkscreen after I test the board. Make it work first then make it look good is my way of thinking.

Good method, Just thought I'd mention it.


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago
David_AVD wrote:Ah, that's what I thought. I made something similar a while back, but that used one byte per step as it had 8 channels.

For the relays, you could get better mains to ELV clearance by choosing relays that don't have the common between the coil terminals.

Thank you for the suggestion David. I really am glad to see that you are looking out for my best interest and I agree that a different choice of relay would provide more clearance. However I believe that this design does provide sufficient clearance. I think that this will be used mostly for 12 volt applications. Things like wiper motors, vent motors and pneumatic solenoid valves. Although if you wanted to use 120 volt reindeer motors or lights that is certainly possible. Lets also remember what we are isolating from the possible high voltage. This controller is not connected to a PC worth thousands of dollars it uses a micro controller that only cost $1.30. Heck the whole circuit comes in at $4.65 so In the very unlikely event that water would get on the board and cause a short its not a real big loss. My plan is to move forward with current design. Again, thank you for your interest and I'm glad to see people are taking time to look at the circuit well enough to see these things and point them out.

Tyler


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

No problems. I wasn't sure of the intended loads so thought I'd chime in.

There are a few improvements I'd do layout wise, but as a hobby design it's pretty good overall. 🙂


Reply
Posts: 13
(@gilles1)
Active Member
Joined: 15 years ago

how about a list off Wat is needed for dis Bord ...Wood lick to try dis


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago
gilles1 wrote:how about a list off Wat is needed for dis Bord ...Wood lick to try dis

I have the parts on order and am still waiting for them to get to me. As soon as I know that all the parts fit and work I will post everything you need to build this board.

Tyler


Reply
tstraub
Posts: 525
Topic starter
(@tstraub)
Honorable Member
Joined: 18 years ago

Just a quick update. All parts have arrived and they do fit testing is underway and all initial this for this 2 channel board look great. I will get the etch files and firmware cleaned up and upload them to the copper section of the File Library hopefully within the next few days.

I have also been working on a similar similar controller that has 4 channels of relay output and stereo MP3 sound output. The 4 channel board still needs some work to get the MP3 playing correctly I hope to get the firmware working soon. This board should cost around $20 to build including the MP3 player module. Here are a few pictures of the 4 channel board currently under development.

IMG 20120906 130831
IMG 20120906 130907
IMG 20120906 130957

Reply
Page 2 / 8
Share: