generic serial setu...
 
Notifications
Clear all

generic serial setup failure

36 Posts
3 Users
0 Reactions
15.1 K Views
Posts: 40
Topic starter
(@keyman6868)
Eminent Member
Joined: 12 years ago

The light is on my mega board. I unhooked the breakout board and all seems to be fine. So that is normal right?


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
keyman6868 wrote:The light is on my mega board. I unhooked the breakout board and all seems to be fine. So that is normal right?

Sorry, but I'm not sure exactly what you are trying to do, or ask.
What have you hooked up and determined that all is normal?


Reply
Posts: 40
Topic starter
(@keyman6868)
Eminent Member
Joined: 12 years ago

Sorry, I'm new at this and I'm trying to learn. Before I got the breakout board I could not connect the vixen3 to my arduino board, in fact the program locked up. after i downloaded the drivers for the breakout board and installed it, the software vixen 3 now see the arduino mega. The green tx flashes fast on the arduino. I could how ever download a simple sketch to the arduino mega and it would work fine.The breakout board is no longer hooked up. Im going to try starting over from scratch again to see if i can duplicate the problem and then I will take a screenshot of what happened! Thank you for your time!


Reply
Posts: 40
Topic starter
(@keyman6868)
Eminent Member
Joined: 12 years ago

I pulled the error log after I started from scratch and this is what i get---
12/31/2014 06:41:48 [VixenModules.Output.GenericSerial.Module] COM3 is in use. Starting controller retry timer for d22c9233-16e9-4008-a215-e577f78a7a2e
12/31/2014 06:43:48 [VixenModules.Output.GenericSerial.Module] COM3 is in use. Starting controller retry timer for d22c9233-16e9-4008-a215-e577f78a7a2e
12/31/2014 06:45:48 [VixenModules.Output.GenericSerial.Module] COM3 is in use. Starting controller retry timer for d22c9233-16e9-4008-a215-e577f78a7a2e
12/31/2014 06:47:48 [VixenModules.Output.GenericSerial.Module] COM3 is in use. Starting controller retry timer for d22c9233-16e9-4008-a215-e577f78a7a2e


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
keyman6868 wrote:Sorry, I'm new at this and I'm trying to learn. Before I got the breakout board I could not connect the vixen3 to my arduino board, in fact the program locked up. after i downloaded the drivers for the breakout board and installed it, the software vixen 3 now see the arduino mega. The green tx flashes fast on the arduino. I could how ever download a simple sketch to the arduino mega and it would work fine.The breakout board is no longer hooked up. Im going to try starting over from scratch again to see if i can duplicate the problem and then I will take a screenshot of what happened! Thank you for your time!

I just loaded a simple Arduino sketch for 8 channels using serial 9600, 8N1. I then open Vixen 3 selected Generic serial found the Arduino com port #11 set it up for 8 channels baud rate 9600 8N1.
The MEGA RX light flickers indicating that it is receiving Vixen data.

So, perhaps your order of doing things may be a factor. On this forum some users insist on a given procedure that works for them. For me, it works if I run the Arduino first, but don't run the Serial Monitor in the Arduino IDE. Then open Vixen and set the COM port #, baudrate, to what the Arduino is using. This procedure has always worked for me.

The "breakout box" is an alternate way for you to use two COM ports, 1) for the Arduino IDE and Serial Monitor, and 2) to receive Vixen data on the breakout box, without the two interfering with each other.

Yes, learning is good... 🙂


Reply
Page 2 / 8
Share: