Conversion to Wirel...
 
Notifications
Clear all

Conversion to Wireless

57 Posts
24 Users
0 Reactions
21.5 K Views
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

Thanks vegaslights.

Replying to what you said,

You can use just the receiver if you are using the start address firmware

What senario would I use the transmitter in?

Yes, provided that they are standard incan lights

All my light strings will be LED. Do they require something different with using the MiniRen8?

I'm getting there, my plan comes together little by little.

Thanks


Reply
Posts: 50
(@vegaslight)
Trusted Member
Joined: 14 years ago

The transmitter would ge from the PC, and if your using them in anything othrnthen broadcast mode.

They will work fine for LEDs as long as they are not DC powered


Reply
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

Just to be clear, They will work with some DC LEDSs using a Ren48lsd, Ren4flood or other Renard boards that use DCSSR's. Xbees will not work in a DMX protocol on the Renards.


Reply
Posts: 50
(@vegaslight)
Trusted Member
Joined: 14 years ago

Thank you xenia. I have not ventured to the dmx stuff yet. However the other cóntrollers could work too... i just use Dirks stuff right now


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

Thank you for all the replies.
I'm going to have to rethink this.

I have viewed the board and BOM for the Ren8/4XB and to me it looks like a minimum of $70 for 4 channels output, and that doesn't include the USB adapter at the PC or the power cords.

I hope I'm looking at it wrong.


Reply
macebobo
Posts: 1595
Guest
(@macebobo)
Member
Joined: 17 years ago

Okay, my 2 cents (and apologies to KyChristmas for continuing the hijack of this thread) - You do NOT need to have one radio for each controller. Controllers that have RS485 in/out can be daisy chained off of one XBEE radio. The only thing having a radio in each controller buys you is flexibility. However, if you have two controllers physically right next to one another, only one of them needs a radio if you can daisy chain them.

11Bravo, if I were you, I would not use the Mini8/4XB (sorry Dirk) for what you want to do. I would recommend the Simple Renard 16LC for the 12 LED strings across your roof and then add a RenW board as your receiver. This will give you the 12 channels you need for substantially less. This is all conditionally on my understanding of what you're trying to do. Also, to your list above, don't forget enclosures, the XBee explorer board, XBee pro radio to transmit, time to build, time to sequence, an FM transmitter, antenna, etc. etc. This is not an inexpensive hobby, but it sure is fun.

** We now return this thread to you KyChristmas 🙂 **


Reply
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

The BOM includes an XBEE at $32.00. You can get these cheaper on Ebay. You generally will find the Xbee Pro Series 1 XBP24-AWI-80 on Ebay for about $18.00 plus shipping. Sometimes you can do even better here from other members. Also the Ren8/8XB will decrease your cost per channel. I know Dirk is out of stock on this right now but should have a new version out shortly.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
macebobo wrote:
11Bravo, if I were you, I would not use the Mini8/4XB (sorry Dirk) for what you want to do. I would recommend the Simple Renard 16LC for the 12 LED strings across your roof and then add a RenW board as your receiver. This will give you the 12 channels you need for substantially less.

John's right about that (and no reason to apologize, John!). I created the MiniRen8/4XB because I wanted what was essentially a wireless 4-channel SSR. It's probably the MOST expensive way you can possibly go (well, I suppose a wireless 1-channel SSR would actually be worse...:lol:)

And he raises a terrific reminder -- the Ren-W can make most ANY Renard board wireless by replacing the wired, cat5 connection with a wireless connection. And while it's certainly very handy to have a 4-channel wireless board, quite often a mid-sized 16 or even 24 channel board with a Ren-W adapter will give you more bang for the buck.

Lastly, when you add up the materials in any BOM for any board, it almost always comes to a staggering amount. Bear in mind that when you order one resistor, or one capacitor, it's very expensive for companies to ship that small of an order and that's why they're so expensive. But that's the only way to calculate a single BOM, by the individual part cost.

Because of this, it's a good idea to make a list of parts that are common to most DIY projects here and order those in bulk. You'll find that 120, 180 and 680 ohm resistors are used everywhere. Same with .1uf and 2200uf capacitors, heat sinks for TA-220 type parts (such as a voltage regulator), DIP-6, DIP-8 and DIP-14 sockets, H11AA1 chips, MOC3023 chips, and the list goes on and on. By having these on hand, you can save a whole bunch of cash over the long run.


Reply
tweist
Posts: 394
(@tweist)
Reputable Member
Joined: 18 years ago

Ok, my 2 cents worth. I converted everything to wireless 3 years ago. At first I had a few problems with moisture getting into the controllers by mounting the antenna on the outside. But this year I tried something new. I am using XBee pro radio's mounted to a 16 channel board. Once the extension cords are connected, the entire thing slide right inside a 4" piece of PVC drain pipe. I drill holes in the bottom cap to enable the cords to come out and I leave the top cap alone. The total tube is about 16" long and is tie wrapped vertically in the yard on a piece of rebar I drive into the ground. This year I had over 40 of these units out in all of the yards. As for distance, again it is line of sight, but I had no problem getting the signal to go over 1000 feet down the block. And the PVC pipe did not degrade the signal at all. All but six of these controllers were communicating with one transmitter. I was pushing 256 channels out of that one transmitter and It never missed a beat. We also had more rain than normal for this time of year, and I did not lose one controller. Its a very simple and cheap way to package things and they worked great.
Hope this helps.

IMG 0147
IMG 0148

Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

Thank you all.


Reply
Page 3 / 6
Share: