I should also have mentioned that I sequence at 50ms timing for I have not yet found a piece of music that needs faster refreshes. At that rate, Renard is limited to 286 channels per com port. I stopped at 280 channels this year because after looking at the available space in my front yard, I decided that if I couldn't do a show with 280 then I wouldn't do a show at all. What that means is that I'll always have to choose what display pieces to use as I plan. I know I can't use all the pieces every year and that's okay. More is not always better, in my opinion. If I had the space and more trees I'd have more capability, and I'd probably do more. But 280 is quite a lot, all things considered. Pixels are all the rage this year, but they're just not part of my plan.
I am just getting started for the first time in a light show setup. I don't have any hardware, just LED lights powered by A/C.
I've been thinking of going the wireless route.
I am not educated yet in the details of what hardware is envolved or how it is layed out between the computer and the load.
Would anyone have a picture of components in the control scheme so I can start adding up the $$ needed purchase the items.
Let say I have 44 items (channels) on my house that I want to sequence wirelessly.
Trying to wrap my head around this.
My question: Does each channel need to have it's own radio transmitter and receiver modules?
Every controler needs 1 xbee, and the pc needs 1 with a usb adapter board.
A controler can have 8 16 or 24 channels on it.
And you need to reprogram the renard boards with a start address.
kingofkya is correct.... each "controller" needs an xbee, not each channel as well as the start address firmware configured on the chips.
For example I have 4 talking skulls that I am going to use for Halloween, each of them is controlled by an MiniRen8/8VOXB (this is an 8 ch low voltage ~1amp per channel); they each have 1 Xbee module and the start address firmware.
In total this will allow me to have 32 Channels to control all 4 of the features and it will require only 4 Xbee's (one per each) to control them.
Likewise I could setup 2 SS16's (each one to control 2 of the talking skulls) and therefor only needing 2 x Xbee's. However I prefer to have them all separate so that I can use them as needed. Cost more, but flexibility and clean installation are more important to me personally.
Hope this helps to clarify it a little more. If not hit me up and I can discuss further.
Hah! You've chosen to come over to the dark side!!!!
I want to come!!!! I want to come!!! Think that is going to be one of my things this year to change over. I bought 8 Xbees last year and have not touched them yet.... DIRK I will need some expertise :biggrin2:
FIRECOP252 wrote:I want to come!!!! I want to come!!! Think that is going to be one of my things this year to change over. I bought 8 Xbees last year and have not touched them yet.... DIRK I will need some expertise :biggrin2:
Same here 4 in my case, but then i realized how mutch cat5 costs, the xbees were cheaper, not to mention ease of use:)
Also don't forget you can daisy chain via cat5 after a wireless controler.
I went all wireless this year(my second year). I have my transmitter in my house by a window and three renw boards inside the ren 24ss enclosure just like the picture in the wiki. One controller is just under my window, one about half way in my front yard(30' or so from transmitter) and a third ren 24 about 40' from transmitter. Everything worked perfect for me I had no transmitting problems at all. It actually cleaned up some com port problems I had while using the db9 connection.
It has already been said but you seem to have your controllers so you should just need the renw or the snap in kits at each controller, then set your start address. I would do the global broadcast mode if possible, lots of room for error using point to point. Cant wait to see what you come up with when you kick the cords!
Thank you,
let me start small with controlling 12 seperate LED strings across my roof ridge to get an idea of how it's done.
Let me know where I go wrong.
I would use three MiniRen8 controllers. Each controller having their own xBee.
Question: Is the Xbee a transmitter and receiver combination? Or does it just receive information only from the PC?
Now, getting power to the controllers.
Would I have to run A/C extension cord to each controller, and A/C cord to each light string.
I am assuming that the MiniRen8 controller has a built in AC to DC power supply? If not, then how does it get power?
Where does the cat5 cable come into play in this senario?
my home is in the middle of 5 acres.
But I will only be concerned with putting lights on the house, and lights out in the front yard within 60 feet of the house and optionally up to 200 feet from the house where I have some trees and hedges. But first I'll be concerned with the house and front yard.
Question: Is the Xbee a transmitter and receiver combination? Or does it just receive information only from the PC?
You can use just the receiver if you are using the start address firmware
Would I have to run A/C extension cord to each controller, and A/C cord to each light string.
Correct, you need to get power to each controller then to ecah of the "channels" for the lights
I am assuming that the MiniRen8 controller has a built in AC to DC power supply? If not, then how does it get power?
Yes, provided that they are standard incan lights
Where does the cat5 cable come into play in this senario?
If you are using a transmitter from the PC to the controllers then there is no cat5, the Xbee's replace that piece.
my home is in the middle of 5 acres.
But I will only be concerned with putting lights on the house, and lights out in the front yard within 60 feet of the house and optionally up to 200 feet from the house where I have some trees and hedges. But first I'll be concerned with the house and front yard.
Just remember "line of sight"; if you can see the antenna from the location where you have the controller(s) then you should be OK
