A DMX controller fo...
 
Notifications
Clear all

A DMX controller for multiple RGB pixel strings

768 Posts
69 Users
0 Reactions
432 K Views
Posts: 64
(@sparky3)
Trusted Member
Joined: 19 years ago

jstjohnz approved schematic


Reply
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago
sparky3 wrote:jstjohnz approved schematic

May want to attach this to the first post, thus making it easier to find. 😉


Reply
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago

Digikey is showing no stock on the prop CPU.


Reply
Posts: 352
(@pmscientist)
Reputable Member
Joined: 16 years ago

Heh, Mouser has the Prop DIP package in stock, but not the SMD. Digikey is the other way around. Go figure.


Reply
Posts: 7
(@sielbear)
Active Member
Joined: 18 years ago

Built both of my E680s tonight, and it was quite straight forward. I hadn't soldered in a couple of years, so it took just a bit to get back in the groove.

One quick question - I didn't see a reference to it in the build plans, nor on the sandevices site, but what were the alternate connections used and why? I ordered and soldered the Molex ones on, and I didn't have too much trouble - perhaps the pain is in making the female connections?

If I understand the female Molex pieces, I essentially crimp the tiny metal pieces onto my bare wirem then insert the little metal pieces with the crimped wire into the plastic housing (in the proper order)? Let me know if I'm off base here.

Perhaps it was finding a small crimper for those little metal pieces? That looks like it might be fun to do...


Reply
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago

There is another type of female connector made by Tyco, the pins are built in to the housing and you push the wires down onto the pins. They are somewhat cheaper, and may be easier than dealing with the separate molex pins. You have the right idea though re the molex parts. If you don't have the proper crimp tool you may find it easier to solder the wires to the pins. Even if you solder you still need to bend the big set of crimp ears in just a bit to be able to slide the pin into the housing. When it goes in correctly it will click and lock in place. It's really a matter of playing with them and seeing what works best for you.

The molex pins can be tricky without the right tool. Several options for crimp tools were discussed a few pages back if you want to go that route.


Reply
Posts: 95
(@cessnapilot)
Trusted Member
Joined: 18 years ago

I got all my parts this week and built my controller yesterday. The build was pretty easy but it was the first build with my new soldering iron so some of the joints aren't perfect. Made 1 solder bridge on the group of 4 330ohm resistors, but since they are all connected I left it.

At this point I haven't tested any strings with it but was able to get to the configuration webpage so I'm guessing everything is working correctly. I will test my GE lights in the next couple of days.


Reply
RPM
Posts: 1080
 RPM
(@rpm)
Noble Member
Joined: 19 years ago

I've attached a picture of some various tools used for the pins on these type of connectors so you can see what they look like.

The tool on the left is one for the individual pins on the CST100 type housings like these.
http://www.tycoelectronics.com/catalog/pn/en/770602-4?RQPN=770602-4
using these type of pins
http://www.tycoelectronics.com/catalog/products/en?q=770666-1

At almost $300 it is the most expensive tool of the bunch.
Here's a link to the Mouser site with the part # 58517-2
http://www.mouser.com/ProductDetail/Tyco-Electronics-AMP/58517-2/?qs=sGAEpiMZZMtArvHj40ttL%252b%252b3PnQrT2jHJSzpiLkBDks%3D

It's a very high quality tool, but slow to use since you need to crimp one pin at a time and then insert them into the connector body.

The middle tool is for the type of connectors that I believe John is talking about. These are the MTA100 type and has the pins as an integral part of the connector.
http://www.tycoelectronics.com/catalog/pn/en/644540-4?RQPN=644540-4
While these are easier to put together since they only are one piece, the wires must be properly inserted or they will be intermittent, or may fall out very easily. They can also be hand soldered, but doing many of these by hand can be tiresome and you will need to remove the pins from the housing first or you will melt the plastic housing.

The tools in the middle and right are for these type of connectors.

The one in the middle is made by ITW Pancon part # MMIT-100F and is constructed of a sturdy reinforced plastic with a metal wire insertion bit.
http://www.newark.com/jsp/search/productdetail.jsp?SKU=95F3536&CMP=AFC-GB100000001
This tool costs about $80 and are pretty good for low volume use. I use this at work for doing mostly repairs on connectors and it works well.

The tool on the right, at about $18 is the least expensive tool. It's a TYCO T-handle tool part # 59803-1. It is also constructed of a reinforced plastic with a metal wire insertion bit.
http://parts.digikey.com/1/parts/357325-t-handle-tool-mta-100-59803-1.html

It's also a low volume type of tool and can be a pain to use. I've used these and I can't remember how many times I've pinched my fingers with it, but it does work.

There are other tools for use with these connectors, but I happen to have these on hand to show you what they look like.

Robert

jstjohnz wrote:There is another type of female connector made by Tyco, the pins are built in to the housing and you push the wires down onto the pins. They are somewhat cheaper, and may be easier than dealing with the separate molex pins. You have the right idea though re the molex parts. If you don't have the proper crimp tool you may find it easier to solder the wires to the pins. Even if you solder you still need to bend the big set of crimp ears in just a bit to be able to slide the pin into the housing. When it goes in correctly it will click and lock in place. It's really a matter of playing with them and seeing what works best for you.

The molex pins can be tricky without the right tool. Several options for crimp tools were discussed a few pages back if you want to go that route.

Connector Tools

Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

When I looked at these, I had decided to get one of the T-handles. Haven't had the time to work on this project yet, and so haven't purchased anything. Thanks for sharing and showing the actual tools!


Reply
Posts: 352
(@pmscientist)
Reputable Member
Joined: 16 years ago

Nice to get a look at the tools, thank you for showing those and passing on some practical knowledge. I take it we should buy some band-aids if we're planning to use the T handle. 🙂


Reply
Page 39 / 77
Share: