Upon review of the Mighty Mini RGB floods that I had purchased, I realized that I didn't actually want to run 24v within my setup, as that would make 3 different DC values to track. Furthermore it would make it that much easier for me to plug in the wrong devices to the wrong controllers and .. well .. in technical terms... Vooomff!!
So, I have drafted out "Yet Another RGBA (amber/white) flood". The board is designed for the 8mm LEDs that were recently purchased in the group buys. I haven't sent these off to manufacture yet, but plan to get a sample run of 10 boards done by the end of August. I will post the gerbers for all to use (ok.. for ANYONE to use), once I have proven that they work.
This board is slightly larger than the MM, as I have "porta-flood" enclosures I didn't feel the need to work so hard to keep the footprint small. These are significantly smaller than the enclosure, but too big for an MM enclosure.
(10cm x 8cm)
The difference in the circuit is that I have 4 parallel channels for each colour, instead of two. So twice the number of resistors and I can then drive these with 12v instead of 24v.
Constructive Feedback is always welcome:
http://doityourselfchristmas.com/forums/attachment.php?attachmentid=7091&stc=1&d=1279794159
Very nice! I love options like that.
I made a similar board although I included a 1N1004 diode in each circuit so I could run it off of 24vac as well as 12vdc. (I had some 24vac wall warts sitting around that looked kinda lonely, so I thought I'd give them something to do.) The diode also allows powering a normal SSR with the 24vac wall wart and feeding the SSR's output directly to the wall washer, eliminating the need for a special DC SSR or DC controller to operate them.
What were the Wall warts from? I've got a WHACK of 9v wall warts (chargers from Cordless phones), but can't imagine what would require 24vac (modems perhaps??)
LabRat wrote:What were the Wall warts from? I've got a WHACK of 9v wall warts (chargers from Cordless phones), but can't imagine what would require 24vac (modems perhaps??)
CCTV Cameras perhaps?
Do I hear a 5v panel?
24VAC is quite common in the industrial world - CCTV, alarms, fire panels, security, and the like.
/mike
n1ist wrote:24VAC is quite common in the industrial world - CCTV, alarms, fire panels, security, and the like.
/mike
I would have expected these to be handled via installed transformers (like doorbells) versus wall warts. But hey.. "ya learn sumthin' new every day"
😎
RE: 5v - I wasn't planning on one.. but it's not outside the realm of reason. It would certainly help to only have the one voltage, instead of two.
LabRat wrote:I would have expected these to be handled via installed transformers (like doorbells) versus wall warts. But hey.. "ya learn sumthin' new every day"
😎RE: 5v - I wasn't planning on one.. but it's not outside the realm of reason. It would certainly help to only have the one voltage, instead of two.
Generally (GENERALLY) the doorbell ect transformers are AC and wall warts are DC, correct?
Yes, one DC voltage would be nice. And wouldn't the 5vdc be a better one to use for our LED lighting direction?
I remember reading something in a MM thread from someone who wanted to modify it for 12V. It was said that Frank used 24V because it would be better for longer runs. Apparently the voltage drop would have a greater effect on lower voltages for a given distance. That being the case I would think that it would have an even greater effect at 5V.
For lower voltages, you end up with more parallel strings of fewer LEDs (assuming you want the same number of LEDs). This will increase the current. Voltage drop in the cables (and in the driver transistors) is proportional to the square of the current, so it will have more of an effect.
/mike
