Yet Another Flood..
 
Notifications
Clear all

Yet Another Flood..

30 Posts
12 Users
0 Reactions
11.5 K Views
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
Skunberg wrote:Generally (GENERALLY) the doorbell ect transformers are AC and wall warts are DC, correct?

While certainly not a thorough survey, when I pawed through a box of used wall warts at a flea market a year or so ago, I found them split pretty evenly between between AC and DC. The vast majority were for low amounts of current (500 milliamps or less).

\dmc


Reply
cenote
Posts: 350
(@cenote)
Reputable Member
Joined: 19 years ago

also, consider this, the higher the voltage, the less voltage drop you will have. 24v on 18g solid over 500', there is nearly no voltage loss, but at 12v, there is a little.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

You should always set the resistor values based upon the actual power supply and cabling you plan to use. The best option is to have an adjustable supply (at least within +/- a volt or so).

Interesting project LabRat - I was initially going to hack my MM boards to run at 12v, then decided to try the LM317 regulators instead which required eight regulators to be installed with 24v but would need 16 with 12v. However - I don't really like the idea of having a 5, 12 and 24vdc setup running of my LSDs as you said so I may go back to cutting them up and using plain 'ol resistors. It looks like pretty easy surgery and that way I can run my Rainbow Floods with my MMs at 12v and any other 12v stuff that comes along...


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

If you use higher voltage for less line loss and then use a large resistor to lower the voltage, Aren't you better off starting with the lower voltage? I suppose I should add the qualifier of a smaller yard, say 200 foot by 100 foot or less. And while I'm on a rant, why don't we use the constant current LED driver on super strips, MM and other floods? Sorry but I need a education on this.


Reply
Posts: 789
(@chilloutdocdoc)
Prominent Member
Joined: 18 years ago
Skunberg wrote:If you use higher voltage for less line loss and then use a large resistor to lower the voltage, Aren't you better off starting with the lower voltage? I suppose I should add the qualifier of a smaller yard, say 200 foot by 100 foot or less. And while I'm on a rant, why don't we use the constant current LED driver on super strips, MM and other floods? Sorry but I need a education on this.

Skun..... say you want to have 30 led's in total, and they each require 2.3v

at 12V the most you'd get in a series is 5

30/5 = 6 parallel strips of 5 led's
6*20mA = 120mA

at 24V the most you'd get in a series is 10
30/10 = 3 parallel strips
3*20mA = 60mA

Half the current. Since the power loss is based upon current, half the current, means half the loss.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Boards have been ordered. My daughter talked me into a BLUE solder mask. At least I won't confuse them with the MM boards I've already purchased.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Shazbat!!!

Boards arrived...

.. they are a thing of beauty. Blue solder mask.. just the right size... an extra four boards ... everything was looking great...

.. until...

As I went to put in one of the 8mm LEDs, I discovered that their legs are much larger than the legs of a standard 5mm LED. So the library part that I made for the 8mm LED in eagle, has holes that are too small for the LEDs legs to fit into. None of the 8mm LEDs will fit on the board.

(Sigh)

Time to re-work the Eagle library... and send off for *another* shipment of PCBs.


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I've done the same thing numerous times. I always print the final tracings out and then actually check for a fit with the parts. I've discovered lots of wierd things...


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

I know how devastating that can be.

I would still build one using 5mm LEDs to prove the concept.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

OOOooooocchhhhh!


Reply
Page 2 / 3
Share: