Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago

OK - minor update - I've been playing with some 2n2222 and MPS2222 transistors that I got from Radio Shack of all places! I rigged up an LED strip simulation driven by 5V and 360mA current which would be the same as a fully populated strip at full on (18x20mA) using some large resistors.

The MPS variety only had 600mA collector current and 625mW power dissipation so they got quite warm (ok - finger print melting hot actually) almost immediately. I switched to a 2n2222 with 800mA collector current and 1200mW power dissipation and it worked great. I let it sit doing some ramps and "sparkles" as well as full-ons for minutes at a time and it worked quite well - barely warm. I'm not suggesting to use RadioShack transisistors so I'll spec a particular one at Mouser. I am still using Renard/DMX code configured in DC mode.

The other thing I am doing is a complete redo of the board using DipTrace instead of ExpressPCB. I really like using ExpressPCB - but w/o the direct Gerber support it really limits your board fab possibilities... DipTrace has a nice auto-router as well as DRC and it's nearly as easy to use as ExpressPCB. It's library is much better also.

Anyway - almost done with the new layout. The other thing I'm playing with is a 5-12V adjustable power supply using a regular 12v PSU as the source. This will allow me to tweak the voltage up/down a bit to the strips. The circuit is pretty easy - it basically uses a stack of four LM338 adjustable regulators to allow for up to 20A! (my supplies are 12V/17A). I found the circuit here - but I will subsitute my existing 12v supply in place of the transformer/bridge/caps section (the transformer is wicked expensive...).


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Linear regulators really aren't the way to go at that current. Just remember that at 20A (5A per regulator), the balancing resistors will dump 7.5W each, and at 5V/20A out from 12V in, the regulators need to dissipate 35W each.
/mike


Reply
Posts: 107
(@michael-sullivan)
Estimable Member
Joined: 19 years ago

If I may offer an idea now we are all moving to directly drive LED's etc could we please start to use more than 4 pins on the RJ45 sockets and waste less cores in the cat5, I love the 48 Chanels for RGB but much better to be able to have 2 sets or RGB per socket and the need for less sockets.

If people want to use SSR's then there are plenty of controllers out there I would just love to see a few LED controllers out there.

I have a new RGB Renard & DMX plugin completed which will be ready for people mid year and will make RGB under vixen a breeze here is a sneak peak at the setup

Cheers
Michael


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
Michael Sullivan wrote:If I may offer an idea now we are all moving to directly drive LED's etc could we please start to use more than 4 pins on the RJ45 sockets and waste less cores in the cat5, I love the 48 Chanels for RGB but much better to be able to have 2 sets or RGB per socket and the need for less sockets.

If people want to use SSR's then there are plenty of controllers out there I would just love to see a few LED controllers out there.

I have a new RGB Renard & DMX plugin completed which will be ready for people mid year and will make RGB under vixen a breeze here is a sneak peak at the setup

Cheers
Michael

Keep in mind that this is specifically to drive Frank's Super Strips which are RGB+W and you have to have a path for the +DC to them. A fully populated strip pulls 360mA for each color so you can't run more than one down a single 24# wire in the Cat5 cable.

I look forward to your new plug-in - RGB is not a lot of fun to sequence with...


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
n1ist wrote:Linear regulators really aren't the way to go at that current. Just remember that at 20A (5A per regulator), the balancing resistors will dump 7.5W each, and at 5V/20A out from 12V in, the regulators need to dissipate 35W each.
/mike

OK - any suggestions - and if possible still utilizing the 12v supplies I have as a source? I knew I would have to heatsink the heck out of the regulators and I was looking at around 8.5A nominal and 16A worst case but I could cut that in half or 4.2/8 to keep everything cooler.


Reply
Page 5 / 48
Share: