Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago

So when is the PCB/BOM Group buy? 😉


Reply
Posts: 789
(@chilloutdocdoc)
Prominent Member
Joined: 18 years ago

As the Beatles would say

Picture yourself in a boat on a [frozen] river,
With tangerine trees and marmalade [lights].
Somebody calls you, you answer quite slowly,
A girl with kaleidoscope eyes.

Cellophane flowers of [bright red] and green,
Towering over your head.
Look for the girl with the [lights[ in her eyes,
And she's gone.


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
dlovely wrote:So when is the PCB/BOM Group buy? 😉

We'll see... gotta make sure the darn thing works first... :rolleyes:

I made up a BOM on Mouser with the assumed components at this point and it was $36.43 for a single set of parts - PCB cost would be variable but a single proto is kinda pricey - but say at 20 boards or so it would probably be ~$20 - maybe less - haven't done the math yet... Anyway - a group buy should get us under $50 for a complete kit - not too bad for 48 channels.

One thing I might do is to disconnect pin 7 from the +DC path on the RJ45s so that you could plug a regular SSR into this as well. Ideally I would connect it to ground through a jumper but this is a tad dangerous because pins 1,3,5&7 are connected together on the strip so if you had a jumper AND a strip you would be shorting your power source across the strip - not good... If I leave it floating it would mean that the LED on the SSRs would not work which is a good compromise. I'm not too worried about the reduced current return of 3 wires vs 4 wires - you could always solder pin 7 to 5 if it was a problem.


Reply
Posts: 604
(@aussiephil)
Honorable Member
Joined: 19 years ago

budude,

What voltages are you specifing for, i seem to have missed that or is it assumed from what you are driving?

Voltage drop, the published spec data dc resistance for Cat5/5e at 26awg is 18-20 ohms per 100m loop, so a 50foot run should have a DC resistance of say 6 ohms and at 360mA will drop 2.16v.

Cable voltage drop is a fact of life for low voltage lighting and can be an issue when not taken into account.

Cheers


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
aussiephil wrote:budude,

What voltages are you specifing for, i seem to have missed that or is it assumed from what you are driving?

Yeah - that part will have to be the variable in the mix as with most DC based stuff - everyone will have to "play" a bit to determine the best voltages at the source, limit resistors on the strips and cabling used - lots of variables unfortunately. This is primarily aimed at Frank's LED strips which have all the LED/drop resistors in parallel so the voltage requirements are low. I would say a 12V supply would probably be the best to start with - add in your actual cables and do some measurements before picking out your drop resistors on the strips. This is why I suggest that everyone use the same length of cable for all of your strips (I used 30') regardless of where you're planning to put them physically...

I'm not sure anything much beyond that (say like 24v) would be a good choice since it will probably toast the regulator at some point (even with a heat sink) and it will might force you into some big resistors on the strips. So if you're dropping 20V even at only 20mA, you're looking at .4W on the resistor so the strips would require 1/2W resistors which may not even fit on them (at least to lay flat...) - heck - even the 1/4W resistors have to bent at very sharp bends to fit into the strips.

All of these issues arise with any of the other DC options such as Franks LV or DCSSRs as well - all part of the fun of DIY! :p

I plan to do some experimenting this weekend with some of my strips. I drove mine with 5v last year but now wish I had configured them for 12v use (especially since I have a pile of stout 12v supplies available...).


Reply
Page 4 / 48
Share: