Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
chilloutdocdoc wrote:Wonderful Design! The only thing I would be cautious of is voltage drop. Cat5 is not the best of conductors for current AFAIK. Even a 50ft run with 360mA is a drop of roughly 7.5%. (somebody want to confirm that?)

YMMV

Thanks - rerouting to get the things in the right order is a real PITA but I'm getting there... Yep - I ran my strips off of DCSSRs last year with 30' cables and accounted for the drop. The key is to make the cables all the same length (within reason) so that the drop is roughly the same to all strips and then adjust your source supply and/or your drop resistors on the strips accordingly.

One thing I have forgotten about is that on my strips with the RGB LEDs that I got, that the Blue and Green colors are swapped. The strips have a series of Red LED resistors, Blue LED resistors, etc. What I found is that the path marked for the "Blue" LEDs lit the Green LED and vice-versa. This is important to know for two reasons. One is if the Blue and Green forward voltages and/or current requirements are different that your drop resistors will be different and you'll put them in the wrong positions - in my case they are exactly the same. The other is that the wiring will be swapped - that is if you don't account for the swap and you wire everything for RGBW and tell Vixen the same - all of your Blues and Greens will be swapped! So - as-is, the strip will be RBGW for pins 2,4,6 and 8 respectively.

The good news is that the easiest way to "fix" this is to swap the wires in your Cat5 cables to the strips. At the strip end I wired them as RBG but at the DCSSR end as RBG and everyone was happy... I hope that is clear to everyone building out the strips. I'll take down one of my strips to clarify this and take some pics.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

I don't know about 7.5%, but the voltage drop in 100 feet (50 feet up, 50 feet back) of 24 AWG wire is about 1V (give or take, since wire resistance charts vary somewhat).

Another way to compensate for the varying wire resistance is to use constant-current sources rather than just a resistor to set the current.


Reply
Posts: 789
(@chilloutdocdoc)
Prominent Member
Joined: 18 years ago

yeah, phil, maybe i was looking at a chart that had a high estimate on the resistance.


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago

OK - updated (see post #1) to reroute all of the outputs so that they would be in RGBW order (that was no fun at all...) as well as having the strips be in order (it would have been 2,1,4,3, etc...). I think I've decided on a name for this - the "Renard 48LSD" or LED Strip Driver... :p

I added in jumpers so that you can partially populate the board if you want. I have to give it one more go over but I think it's pretty close at this point - just have to decide which transistors/resistors to use for the outputs.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
budude wrote: I think I've decided on a name for this - the "Renard 48LSD" or LED Strip Driver... :p

Tommy Chong would say...

WOW, MAN...LIKE... QUITE A COOL TRIP YOU'RE TAKIN' US ON, MAN... :rolleyes:


Reply
Page 3 / 48
Share: