Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.6 K Views
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
LabRat wrote:UHmm.. but if the 48LSD is being controlled by an incoming DC source.. you don't have zero cross.. so you wouldn't be able to dim the ACSSR's anyhow.
So (to me) this really doesn't seem a logical/viable solution.

(Again.. I suspect I'm not seeing the forest for the christmas-trees here)

The 48LSD is a powerful DC solution... none-better that I can think of. To me, however, it doesn't make too much sense to drive the ACSSR's with it.

The opto in a normal A/C ssr is triggered by DC voltage, and with PWM firmware loaded on the 48LSD, the A/C ssr won't know the difference. It'll work fine -- and does.:cool:


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Lol, I was researching the PWM firmware and the Ren48LSD because I was remembering that the PWM firmware can still "dim" AC lights I just wasn't sure, then I scroll down and see that Dave already posted that, lol.


Reply
Posts: 151
(@bf210)
Estimable Member
Joined: 18 years ago
dirknerkle wrote:The opto in a normal A/C ssr is triggered by DC voltage, and with PWM firmware loaded on the 48LSD, the A/C ssr won't know the difference. It'll work fine -- and does.:cool:

The need for zero-cross in simple AC dimming is pretty well established. If you're getting reliable PWM dimming from AC SSRs without a zero-cross detector in the controller, then your load might be light enough that the triacs aren't latching on. Try a few more tests with larger loads and steady 30% or real slow fades and look for flicker or pulsing.


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
BF210 wrote:The need for zero-cross in simple AC dimming is pretty well established. If you're getting reliable PWM dimming from AC SSRs without a zero-cross detector in the controller, then your load might be light enough that the triacs aren't latching on. Try a few more tests with larger loads and steady 30% or real slow fades and look for flicker or pulsing.

I've seen lots of folks use nothing but PWM code for all their controllers regardless of using AC or DC or light vs heavy loads? I thought the main advantage of using non-PWM was that there was significant power saving to be had since it only needed to send a single pulse to the TRIAC to turn it on vs being on for the full "On" time.


Reply
Posts: 789
(@chilloutdocdoc)
Prominent Member
Joined: 18 years ago
budude wrote:I've seen lots of folks use nothing but PWM code for all their controllers regardless of using AC or DC or light vs heavy loads? I thought the main advantage of using non-PWM was that there was significant power saving to be had since it only needed to send a single pulse to the TRIAC to turn it on vs being on for the full "On" time.

The PWM code does indeed reduce the power saved, HOWEVER you still need a zero cross signal in order to do AC dimming properly with triacs. Explanation as follows (correct me if i'm wrong)

We use a latching triac, that means, when it turns on, it does not turn off until it has no current running through it. This occurs everytime the AC signal passes 0. AC has a natural sine wave curve.

Each time the Voltage level (represented by the y axis, time is the x axis) is 0, there is no current possible. If the channel was at 100% it would stay on the entire time, turning on as soon as the votage went above (or below) 0V. 50% would mean that the triac is OFF the first half of the "U" shape, and ON the second half. 25% the triac would be OFF the first 75% and on the last 25%. The signal must be in sync with the Zero Cross (when the curve meets the x axis 0V) or else it could not work out. Example: 50% not sync'd, worst case scenario, the triac would turn on during the first 50%, but due to it's latching nature, it would remain on the rest of the cycle, thus lighting at 100%.

I hope this made some amount of sense, if i wasn't clear, or was wrong on any portion, please let me know, thanks!


Reply
Page 38 / 48
Share: