Simple Renard Strob...
 
Notifications
Clear all

Simple Renard Strobe Burst

124 Posts
29 Users
0 Reactions
52.3 K Views
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
ChiefWarrant wrote:Mac,

These ( http://www.bcwsupplies.com/products/Golf-Ball-Display-Cases/Golf-Ball-Square.htm ) may work for your burst module.

- Holds a regulation sized golf ball
- Crystal clear
- 2 piece design

Dimensions
- Exterior 2 1/4 x 2 1/4 x 2 1/4
- Interior 2 3/16 x 2 3/16 x 2 3/16

Tony

Hey Tony,

The PCB is 2.8 inches x 2.8 inches with snap off tabs so they will not fit in them, sure wish I could make the PCB smaller without having to go to SMT parts.

Mac


Reply
ChiefWarrant
Posts: 570
(@chiefwarrant)
Honorable Member
Joined: 19 years ago

Mac,

They also have hockey puck holders ( http://www.bcwsupplies.com/products/hockey-puck-display-cases/puck-holder.htm ) for about $0.10 more. They are 3.125" square.

Tony


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Widget supply has some nice plastic containers that look likey they might work, too... and very cheap!

http://www.widgetsupply.com/page/WS/CTGY/storage-plastic-container


Reply
mlkren
Posts: 745
(@mlkren)
Prominent Member
Joined: 16 years ago

What about this. A little more expense but seems like a great solution.


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

But this: http://www.kfc.com/packaging/container.asp is free with lunch or dinner!


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
CaptKirk wrote:But this: http://www.kfc.com/packaging/container.asp is free with lunch or dinner!

But then you'd have to eat KFC, which — as the wife points out — always smells better than it tastes.

\dmc


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Except the cole slaw tastes better than it smells AND comes in a Renard Strobe Burst waterproof case (at least I hope so)! The grilled stuff is pretty good too... 😉


Reply
Posts: 40
(@pyrotech)
Eminent Member
Joined: 16 years ago

Hi has this progressed further? and on a flight of fanciful thinking , could the module act as a hub for leds, to make a 3d shape, I mean simple connectors on the board, then the LED's on assorted short lengths of cable hanging upside down? like mistoletoe berries or a 60's lighting fixture? Without the led's in-situ the board size could be reduced.


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
Pyrotech wrote:Hi has this progressed further? and on a flight of fanciful thinking , could the module act as a hub for leds, to make a 3d shape, I mean simple connectors on the board, then the LED's on assorted short lengths of cable hanging upside down? like mistoletoe berries or a 60's lighting fixture? Without the led's in-situ the board size could be reduced.

This is not dead by any means, I am waiting for the SR RGB+W PCB's to arrive so they can be tested, then the SR Strobe Burst and the SR LCC16 will go out to the PCB house and once they arrive I will post some info on them. I do like your idea about the 3D and mistletoe berries.:)


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago

Well I thought it was time to start working on this project again and I found out that I could use a Simple Renard 32 to control the Strobe Burst Modules so I made a Strobe Burst Splitter that takes 4 channels of the SR 32 and will convert the signals so that 4 Strobe Burst Modules can be connected to one cat5 cable then redirect wiring to each module and I also reduced the size of each module to less then a 2 inches on all sides with corner snap offs so with one Simple Renard 32 you can control 32 Strobe Burst Modules,,, on/off and dimming for the strobes.. I have attached some files and I will soon be getting some Proto pcb's for testing.


Reply
Page 4 / 13
Share: