Am I correct in thinking that a 74HCxxx device can safely handle somewhere around 100mA, even though the datasheet only says 75 mA?
I've seen in some of ON Semi's 74HCxxx datasheets that the max DC supply current (Icc) for Vcc or Gnd is listed as 75 mA, but the total power dissipation for the device is 500 mW or higher. The datasheets say to refer to the "ON Semiconductor High−Speed CMOS Data Book (DL129/D)" for more details, so I did - maybe I shouldn't've. 😉
I found a note in there that the published Icc value is for the "worst case" Vcc, which is listed as 6V. Since Power Dissipation = Icc x Vcc (+ a bunch of dynamic/parasitic stuff that also has Vcc in it), and they are using the worst case value of Vcc = 6V for the datasheets, then that would seem to imply that if I used a lower Vcc (like 5V), then I should be able to run the device (safely) with Icc @5V = 6/5 x Icc @6V = 1.2 * 75 mA = 90 mA, or Icc @4V = 6/4 x 75 = 112.5 mA, etc.
Would this be considered staying within the safe limits of the device?
don
Doesn't the data sheet specify the maximum source and sink values? That would be my guide. Make sure you check the data sheet for the specific brand of chip (and package) you intend to use.
David_AVD wrote:Doesn't the data sheet specify the maximum source and sink values? That would be my guide. Make sure you check the data sheet for the specific brand of chip (and package) you intend to use.
Yes, it lists the per-pin limits as well as the total DC supply limit (which is the Icc that I was refering to). But in reading further into it, I came across the note about 6V worst case, which then lead me to question whether it is accurate to take the published Icc limit at face value.
For example, ON's 74AHC00 datasheet says that max Vcc = 7.0V and max Icc = 75 mA max, but the DL129 publication says that they used Vcc = 6V to determine Icc.
don
I just checked the NXP data sheet and it's pretty clear. The output current is 25mA max per pin, with 75mA max each for supply (Vcc) and ground (Vss) pins.
I think you're only considering what happens when you source current from the outputs. You've seen the 5V (Vcc) and the 75mA (Icc) and come up with 375mW, not the 500mW total allowed.
But... remember that the outputs can source or sink current. The output current in sink mode goes through Vss, not Vcc, hence it is included in the Ignd.
The 500mA Ptot figure would largely be the sum of the dissipations in the source and sink elements. This is the pin's Iout multiplied the source or sink saturation voltage.
So, the 75mA is the hard limit for a simple source or sink case. Clear as mud?
David_AVD wrote:Make sure you check the data sheet for the specific brand of chip (and package) you intend to use.
d'oh - part way along the trail I got mixed up between ON Semi and NXP.
I had a look at JESD7-A, and it says Icc is 50 mA for non-bus driver 74HC, so it looks like the 74AHC00 provides more than the spec.
David_AVD wrote:But... remember that the outputs can source or sink current. The output current in sink mode goes through Vss, not Vcc, hence it is included in the Ignd.
Good point. I forgot to check current in the other direction, which is actually the only case that I need anyway. Should I maybe look at open collector parts instead?
David_AVD wrote:The 500mA Ptot figure would largely be the sum of the dissipations in the source and sink elements. This is the pin's Iout multiplied the source or sink saturation voltage.
This is what lead me to question the 75 mA as an absolute limit, because 5V * 75 mA = 375 mW, which is less than the 500 mW figure given, but 5V * 100 mA = 500mW. So I was trying to track down that extra 25 mA. Is it in the "dynamic" portion of the equations, when the device is switching?
David_AVD wrote:So, the 75mA is the hard limit for a simple source or sink case. Clear as mud?
Thank you for the explanations! I think my problem is that I don't have a good mental model of all the flows into and out of an IC.
At the risk of confusing myself further, what would be an example of a case that is not "simple", and would that relax the 75mA restriction any? Is it just a question of whether the device is changing state vs. sitting in a steady ("quiescent") state?
don
