Simple Renard Strob...
 
Notifications
Clear all

Simple Renard Strobe Burst

124 Posts
29 Users
0 Reactions
52.3 K Views
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Ok. So someone had to ask the question... Is there a way to run these off a MiniRenxxx or would we need a Ren-W to go wireless and have to use the SR32 to drive the strobe modules?


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
mschell wrote:Ok. So someone had to ask the question... Is there a way to run these off a MiniRenxxx or would we need a Ren-W to go wireless and have to use the SR32 to drive the strobe modules?

The board has connectors for +5v, G and a trigger, so it looks like it's a constantly free-running board (with the 555) that lights up only on a trigger pulse, which comes from a controller. I'm sure it's designed to work with the Simple32, and as such, it would use the PIC's outputs as the trigger. Any of the MiniRen boards have direct access to the PIC outputs, but the MiniRen's transformer most likely won't provide enough current to drive many of these.

I'm thinking it should work with the MiniRenServoXB, which has connections for external supply power as well as the trigger, but I've got to build one of the strobe bursts before I can test it...


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Famed Member
Joined: 17 years ago
dirknerkle wrote:The board has connectors for +5v, G and a trigger, so it looks like it's a constantly free-running board (with the 555) that lights up only on a trigger pulse, which comes from a controller. I'm sure it's designed to work with the Simple32, and as such, it would use the PIC's outputs as the trigger. Any of the MiniRen boards have direct access to the PIC outputs, but the MiniRen's transformer most likely won't provide enough current to drive many of these.

I'm thinking it should work with the MiniRenServoXB, which has connections for external supply power as well as the trigger, but I've got to build one of the strobe bursts before I can test it...

Each channel/strobe module will draw 12ma when turned on at full intensity,,, so 8 channels will consume 96ma...from the +5 volt supply


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago
dirknerkle wrote:The board has connectors for +5v, G and a trigger, so it looks like it's a constantly free-running board (with the 555) that lights up only on a trigger pulse, which comes from a controller. I'm sure it's designed to work with the Simple32, and as such, it would use the PIC's outputs as the trigger. Any of the MiniRen boards have direct access to the PIC outputs, but the MiniRen's transformer most likely won't provide enough current to drive many of these.

I'm thinking it should work with the MiniRenServoXB, which has connections for external supply power as well as the trigger, but I've got to build one of the strobe bursts before I can test it...

Trying not to drag this too far away from on-topic discussion, but assuming that I had +5v external supply that could feed the MiniRen. could we do it wirelessly that way? I'm trying to minimize components and limit the need for a wired connections in the yard. I'm thinking of a package of a MiniRen (8 channel), perhaps two breakout modules and a power supply in a small case, with wires running to 8 of the Strobe Burst modules.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I think that would work. That's essentially the kind of setup I plan to test. In wireless mode, using a regular XBee module will require less current than a Pro model and leave more juice for the rest of the board but even at 12ma/channel, that 96ma total is pushing the PIC16F688 pretty hard -- that's right at the very edge of what the PIC can manage... of course, you don't have to drive the units at 100% either.... I doubt you'd notice much difference between 90% and 100% in terms of brightness and that would put your current draw on the pic down into the mid-80's... a little breathing room there...


Reply
Page 20 / 25
Share: