If I used the same resistors as the ones used in the ren-c to grinch convertor with 24vac would that work? As I've got loads of them hahah
Steve
soakes94 wrote:If I used the same resistors as the ones used in the ren-c to grinch convertor with 24vac would that work? As I've got loads of them hahahSteve
what value resistor are you using? make sure your cap on the input of the VReg is rated at least 50VDC, you will be dissipating a lot more heat through the voltage regulator using a 24VAC transformer and you will need a heat sink on it.
edit,,, BTW are going to use DC SSR's or AC SSR's, if you are going to use DC SSR's you will not need the H11AA1 and the two ZC resistors, they are only needed for AC SSR's.
hi all - I was developing a Picaxe based demux running on the generic serial protocol, but realised after rushing it for this Christmas that I was actually just re-designing something that already existed. Where can i get the firmware and details for the Renard 32?
Cheers
Rob
Start at the beginning of this thread. By the time you get to post 17 all should be clear. 😉
relewis wrote:hi all - I was developing a Picaxe based demux running on the generic serial protocol, but realised after rushing it for this Christmas that I was actually just re-designing something that already existed. Where can i get the firmware and details for the Renard 32?
Cheers
Rob
Here is the info on the SR 32. The reason you will not find any info in the Wiki is due to the DIYC site crash back in November, I was almost finished entering all the info in the Wiki and the site went down for a week,, when it came back up the info I entered was all gone.. As you probably already know the site is not back up 100%. After It is back up and fully functional I will re-enter all the data again. For now I included a few files. Hope this helps. Here is the link to the PCB's if you are interested in them. http://n7xg.net/diycprojects.html
Cheers Mac - you're a star.
To date I've only ever played with picaxe which has a basic bootloader, so this should be fun - not done Hex programming since ZX spectrum days!
I've got some 18f4520 - will these be ok?
For my first Renard build I'm planning on redesigning the pcb from scratch as I have a couple of 16 channel opto-isolated clickety-clackity relay boards which i used for this year's display on the back of a couple of picaxe chips. They are available off ebay for around £16. Beyond that I'm looking at dimming for next year, so will do this on something a little more standard.
Love the single-chip 32-channel idea. Looks like a real move forward.
This years (small) display is on youtube - search for bigpaperaeroplane
cheers
Rob
(UK)
relewis wrote:
I've got some 18f4520 - will these be ok?cheers
Rob
(UK)
Rob,
The PIC 18F4520 is an excellent choice. I ran 3 SR32s this year(2 home etched and 1 production board). Mine were fitted with one of each 18F4520, 18F4620, and 18F4525. All performed flawlessly all season. I had some problems with my SSR's due to a lot of rain but all of my Simples worked just fine.
good luck
Tyler
I've etched the board and fitted most of the bits -just waiting on the opto.
I had a little issue getting the firmware onto the 18f4520 pic - probably my fault for using a cheapy £17 pic programmer off ebay.
After squirting in the hex it would come back with an error. However i found if i told the programmer that the chip was a 18f4620 all was well.
It will be interesting to see if it actually worked!
I had a rethink and etched the board as standard and am making an intermediate interface board to go between the 32 and my relay boards.
Can anyone point me to a low-current 32 channel SSR board?
cheers
Rob
relewis wrote:I've etched the board and fitted most of the bits -just waiting on the opto.
I had a little issue getting the firmware onto the 18f4520 pic - probably my fault for using a cheapy £17 pic programmer off ebay.
After squirting in the hex it would come back with an error. However i found if i told the programmer that the chip was a 18f4620 all was well.
It will be interesting to see if it actually worked!
I had a rethink and etched the board as standard and am making an intermediate interface board to go between the 32 and my relay boards.
Can anyone point me to a low-current 32 channel SSR board?
cheers
Rob
Hi Rob,
I do not know of any low-current 32 SSR boards and then again I am not sure what you are trying to do,, are you wanting to use relays or SSR's, if you are looking for SSR's there are a few to choose from SSR8's, SSREZ or SSRneons, take your pick.. As for the problem of your programmer not being able to load the firmware into the PIC18F4520 it could be as simple as selecting the correct device in MPLAB.. I am including an MPLAB file that has the correct firmware for a PIC18F4520, the one you used could of been setup for a PIC18F4620 which is not the same device so I would stick with the firmware for the PIC18F4520..hope this helps
Any thoughts on doing the DMX firmware on this baby? I'd love to do this board with the Strobe Pucks on a DMX setup!!
