Don,
I read your PDF straight-through this past weekend and themes that kept repeating themselves were how frequently you had to borrow on your ingenuity and DIY skills to overcome an obstacle, how you evaluated the result and what you might have done/are planning to do differently the next time. In nearly each case, you reverted to (a) practicality, (b) cost-effectiveness and (c) immediate convenience. There was cause-and-effect methodology and success measurement included throughout, and all this points to a project that was extremely well conceived in-mind and implemented using a good road map. All in all, it was extremely well done, and (at least by me) very, very much appreciated.
I've had a somewhat similar idea in mind to use basic Vixen pixel mapping for the purpose of sending a text message to a "Dumb-Triks" board and I'll certainly use your manual as a template for documenting my progress. My idea involves creating a new Vixen plugin (of course) for converting a line of text into Vixen pixels and a modified version of Renard code at the board end to decode the designated channel information into the LED display. I think I can get it all done with a block of only 8-channels where one of the channels contains the appropriate control signals to accept the text message and then display it repeatedly until the next messsage is received or the message overwritten with blanks, which effectively deletes it. In my mind (what little there is of it) I see this using the standard Renard plugin for sending the data out to the controller and the remote Dumb-Triks board would be set to the appropriate start_address to grab the channel information.
So thanks in advance for giving me a little roadmap of my own to follow.
-dave
Re: How i did: Dumb RGB Pixel Grid
dirknerkle wrote:I've had a somewhat similar idea in mind to use basic Vixen pixel mapping for the purpose of sending a text message to a "Dumb-Triks" board and I'll certainly use your manual as a template for documenting my progress. My idea involves creating a new Vixen plugin (of course) for converting a line of text into Vixen pixels and a modified version of Renard code at the board end to decode the designated channel information into the LED display. I think I can get it all done with a block of only 8-channels where one of the channels contains the appropriate control signals to accept the text message and then display it repeatedly until the next messsage is received or the message overwritten with blanks, which effectively deletes it. In my mind (what little there is of it) I see this using the standard Renard plugin for sending the data out to the controller and the remote Dumb-Triks board would be set to the appropriate start_address to grab the channel information.
Sounds like a cool project! Is the Dumb-Triks a row/column matrix of LEDs, charlieplexed, or another type of structure?
Also, thank you for the comments about the article.
don
Re: How i did: Dumb RGB Pixel Grid
djulien wrote:Sounds like a cool project! Is the Dumb-Triks a row/column matrix of LEDs, charlieplexed, or another type of structure?Also, thank you for the comments about the article.
don
I'm not really thinking about charlieplexing, but instead using an array of cheap 595 chips, one for each column of 7 LEDs x however many columns you want in your display. The PIC would store the data and continuously scroll the contents of its memory across the columns. The unused channel of the set of 8 channels would be used for sending various control codes to the PIC to tell it to load data or display data. To clear the display, you'd send blank cells, which would turn all the LEDs off but otherwise, it would continue to run until cleared, powered off, etc. I haven't chosen the PIC yet as I have to flush out a few thoughts first, but if you think of a character as a 5x7 display (35 bytes) there's enough room in a 16F688 to try the concept with up to about 32 columns of LEDs allowing about 6 scrolling characters on-screen at a time. Persistence of vision and the brain can assemble the words from there as the data scrolls across the columns.
My vision is actually to be able to "read" the text as if you had drawn it in pixels inside Vixen, so in a way, it would be self-documenting. The plug-in would select the channels to use (on an 8-channel boundary), you'd type the text into a text box and it would convert it into pixels which you could copy/paste wherever you wanted them in the sequence for the channels assigned to the board. And being that a song usually spans several minutes, there would/should be ample opportunity to display multiple messages.
Part of my goal is to create a very low-cost Triks effect doing something quite close to what you've done with the Dumb-RGB Grid, although not in a charlieplexed setting. I'm actually thinking that this whole concept could quite possibly be accomplished with a couple Olsen595 boards and a "driver" board similar to the Ren-C, which would extend the usefulness of the venerable old workhorse 595... 🙂
So I need to tame the bats flying around inside my head before jumping into this too far...
Re: How i did: Dumb RGB Pixel Grid
dirknerkle wrote:I'm actually thinking that this whole concept could quite possibly be accomplished with a couple Olsen595 boards and a "driver" board similar to the Ren-C, which would extend the usefulness of the venerable old workhorse 595... 🙂
Yes, it sounds like that would work.
Are you thinking of using monochrome or RGB LEDs? Even with just on/off control and no dimming, you could get the 7 basic colors with RGB LEDs. If the on/off control is at least ~ 60 Hz, then you could also get other colors.
don
Re: How i did: Dumb RGB Pixel Grid
djulien wrote:Yes, it sounds like that would work.Are you thinking of using monochrome or RGB LEDs? Even with just on/off control and no dimming, you could get the 7 basic colors with RGB LEDs. If the on/off control is at least ~ 60 Hz, then you could also get other colors.
don
I'm really thinking of this as a truly dirt-cheap method to create a moving text display so monochrome is the original development mode. Being that one can buy 100 LEDs for peanuts, or even cut up a string of LEDs and use them instead, my goal is to make this a project for $20 or less.
