Simple Renard 32
 
Notifications
Clear all

Simple Renard 32

103 Posts
25 Users
0 Reactions
56 K Views
Materdaddy
Posts: 2368
(@materdaddy)
Famed Member
Joined: 16 years ago

Looks like I'm going to need some help here.

I cannot get this thing working. The wiki page says the status light will go bright, dim, dimmer when the PIC is programmed and ZC is working. I have that, but it's not very "clean". It seems as though sometimes it is a half second between bright and dim, then only 1/4 second between dim and dimmer. Seems jumpy. In addition, sometimes it alternates off->dimmer->dim->bright (getting brighter instead of dimmer).

if I set the PIC bypass jumper, I can get a downstream renard device working (to verify vixen/RS485) but with the normal 2/3 setting, nothing. I believe something is slightly off with my PIC programming. I doubted my compile using MPLabX so I downloaded the hex a couple posts up (since I'm using 57600) and it has the exact same behavior.

Any ideas on what I should be trying next?


Reply
mbasile35
Posts: 53
(@mbasile35)
Trusted Member
Joined: 15 years ago
Materdaddy wrote:Looks like I'm going to need some help here.

I cannot get this thing working. The wiki page says the status light will go bright, dim, dimmer when the PIC is programmed and ZC is working. I have that, but it's not very "clean". It seems as though sometimes it is a half second between bright and dim, then only 1/4 second between dim and dimmer. Seems jumpy. In addition, sometimes it alternates off->dimmer->dim->bright (getting brighter instead of dimmer).

if I set the PIC bypass jumper, I can get a downstream renard device working (to verify vixen/RS485) but with the normal 2/3 setting, nothing. I believe something is slightly off with my PIC programming. I doubted my compile using MPLabX so I downloaded the hex a couple posts up (since I'm using 57600) and it has the exact same behavior.

Any ideas on what I should be trying next?

Not sure about the status led, but the second half sounds like the same issue that Mac just helped me resolve. I may be wrong, but i could have sworn that the wiki said the firmware hosted in the library was for a 57600 baud rate but then Mac said that the file in the library was for 115200. So he updated the file in the library to be for a 57600 baud rate. Try to download the zip again and reprogram your pic. Or just use a baud rate of 115200 if you can and see if that helps

Mike


Reply
Materdaddy
Posts: 2368
(@materdaddy)
Famed Member
Joined: 16 years ago
mbasile35 wrote:Not sure about the status led, but the second half sounds like the same issue that Mac just helped me resolve. I may be wrong, but i could have sworn that the wiki said the firmware hosted in the library was for a 57600 baud rate but then Mac said that the file in the library was for 115200. So he updated the file in the library to be for a 57600 baud rate. Try to download the zip again and reprogram your pic. Or just use a baud rate of 115200 if you can and see if that helps

Mike

Thanks for the suggestion, but unfortunately I have already tried that. I used 57600 and even tried the hex file Mac posted which he said was compiled for 57600 as well. I changed the "inc" to use 57600 and no start address. I know the vixen side is working because of the SS8 I'm using to ensure that part is still working and help eliminate one variable. I'm still suspecting MPLabX and my compilation/programming of the PIC.

One thing I notice. When I load the hex (that Mac provided a few posts ago) into a project and program, the "Pickit2" console shows it programming the "Program Memory" as well as "EEPROM", but when I compile the code from source, I only see it programming the "Program Memory" not the EEPROM. Neither are resulting in successful behavior of the SimpleRen, but just another note for those that know more about this than me.


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Famed Member
Joined: 17 years ago

Hi MD,

I have had no luck using MPLabX,, I am using MLab IDE 8.73 and it works fine... did you use the hex file that I added to file library last night named
http://doityourselfchristmas.com/forums/dynamics/showentry.php?e=106&catid=6 and are you using a PIC18F4520.

make sure you have a shunt accross pins 4 an 5 of JP1 (RenW Header) or it will not work.


Reply
cparsons2391
Posts: 160
(@cparsons2391)
Estimable Member
Joined: 16 years ago
I cannot get this thing working. The wiki page says the status light will go bright, dim, dimmer when the PIC is programmed and ZC is working. I have that, but it's not very "clean". It seems as though sometimes it is a half second between bright and dim, then only 1/4 second between dim and dimmer. Seems jumpy. In addition, sometimes it alternates off->dimmer->dim->bright (getting brighter instead of dimmer).

I don't know if this helps any, but my status light seems to do the same thing! If I remove the ZC chip (H11AA1) it flashes. I have not tried seeing if it is working with the computer. I am waiting for DMX firmware to be released.


Reply
Page 19 / 21
Share: