Renard - PIC16F688 ...
 
Notifications
Clear all

Renard - PIC16F688 Replacement

23 Posts
11 Users
0 Reactions
9,644 Views
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago
[#25672]

There are rumors out there about the PIC16F688 being discontinued at some point by the manufacturor. While I am very skeptical about this, there is new, better part which can replace the PIC16F688 on the Renard boards, namely the PIC16F1825. It cannot use the same firmware image as the PIC16F688, but I've created firmware for this part and uploaded it to the file library. I'd like to encourage people to buy a few of the new part and try this firmware out, so that this part can eventually be phased in for individual and group buys.

BTW, this is not an urgent matter, as I think the old part will be available for a long time. I view this is a low-key, routine matter.


22 Replies
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Nice work Phil !
Shoot, if anyone else is like me, I have enough 16F688's to last for years !
But, it's good to know it was this easy to find a pin for pin replacement.
I'm not surprised by this. Microchip would be foolish to obsolete folks boards that use a particular pic in the commercial world without an easy replacement.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

To date, microchip has never obsoleted a single micro. According to their sales and engineering reps, there’s no intent to do so anytime soon.


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago
ErnieHorning wrote:To date, microchip has never obsoleted a single micro. According to their sales and engineering reps, there’s no intent to do so anytime soon.

That's good to hear.


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago
ErnieHorning wrote:To date, microchip has never obsoleted a single micro. According to their sales and engineering reps, there’s no intent to do so anytime soon.

Yes I would expect Microchip sales and engineering to say that (what company would ever admit they screwed over customers??), but what is the REAL truth? Look up a Microchip PIC16C84 for one example- yes there is a similar replacement for it, but if you actually needed the specific 16C84, it is not made any more. I am sure there are more examples- there always is, even with great companies like Microchip!!


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

The C84 is a really really old chip and I don't blame them for dropping it. I threw a heap of those out a couple of years ago.

Sent from my AMI-TT2 using Tapatalk 4 Beta


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

Other than modifying the code because the PWRTE bit is inverted, the PIC16F84A is likely a drop-in replacement. I doubt that there is anybody that could justify using a CMOS micro. The 16C84 had some issues that were fixed in t 16F84.

I can’t imagine why anybody would want to go back to the CMOS versions.

I was also told that if you wanted sufficient quantities to justify the cost to you, they would still make these.


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

Porting the code to a newer (and often cheaper) chip is usually pretty painless.

Sent from my AMI-TT2 using Tapatalk 4 Beta


Reply
Posts: 6728
Topic starter
(@p-short)
Illustrious Member
Joined: 20 years ago

Not in the case of PIC16F688 to PIC16F1825, as the memory mapping is different and interrupts behave somewhat differently. Not rocket science, but not just a one or two-line change either.


Reply
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago
P. Short wrote:Not in the case of PIC16F688 to PIC16F1825, as the memory mapping is different and interrupts behave somewhat differently. Not rocket science, but not just a one or two-line change either.

I second that. Working on changing the RenServo firmware over and its a real pain.

Dave


Reply
Page 1 / 3
Share: