I was talking to a friend with a small business and mentioned that Xlights would do a nice full color sign. Well, I showed the software and now they want a sign. We picked a resolution of 16x75, which is two text lines and eight universes of pixels.
Rather than using my other 32 universe controller, and waste the unused ports, I decided to do a scaled down board with eight universes. This board will support Ethernet E1.31 to the following outputs DMX, Renard at 56K, 115K, 230K, and 460K, WS2801, WS2811, for now. With each set of four universes supporting the same pixel types, except for one setting with two each of Renard/DMX. The pixels can be driven directly from the board, and there will be two headers to support the DMX, Renard buffer board outputs. Let me know if anyone has extra features that they are interested in.
I was thinking about putting on an accelerometer chip, so I could eventually do a spinning sign. I would probably need a RS-485 receiver to go with it.
Getting ready to order the board and the parts. If anyone is interested in one fully built for say $40 let me know in the next week. I will probably do no more than five for the initial run.
The board is on order and the pixels have been shipped from Ray.
The parts cost is about $28 without the board for a set of one. Can probably shave another $3 off for a set of one, but quantity should help on the price.
Will post pictures and maybe a final video of the project as I go along.
It has been a good weekend, and I have made some progress on the sign. I really like programming for FPGA's, cause I can just copy the code, change the pins and it works. Anyway, got my controller working with 4 WS2811 LED's from Xlights. So I know the Ethernet works on a double sided board, and that the firmware is good, so I just need to finish wiring the sign. I have enclosed pictures for my progress. I am waiting on the power supplies from Ray. When I have the glorious 1200 LED's glowing get some shades, I will post a video.
How did I miss this post?? I'll take one. Do you have another available?
I will like to add this to my collection of controllers.
Great looking board! :thup:
Completed the soldering for the power and the control signals. Injected the 5.0Vdc power in the center of each of the strips to minimize voltage loss. Also, have my $40 eight universe controller running the show. I have enclosed a short video of the controller running simple nutcracker sequences for demonstration. My power supplies have shipped so I just have to build a frame and install the power supplies.
Great looking effects.. What is the matrix made up with. size spacing etc... even pics
Tom
tmcteer wrote:Great looking effects.. What is the matrix made up with. size spacing etc... even picsTom
The pixels are WS2812B from Ray, at a spacing of 60 LED's per meter. The sign resolution is 75x16, and the sign ends up being about 4 feet by 12 inches.
Do you still have any of these available? If so I'll take one, if they're assembled. I don't have the capability to solder surface mount parts.
Thanks,
-joni-
are these strings or individual leds? and what did you use to mount the leds and can i buy 2 boards and make it twice as big.
I have ten boards on order, they have shipped, so I am expecting them any day. I will have some available in 2-3 weeks and will contact you to see if you are still interested.
The LED's are made up of strips of individual LED's. Each strip is 75 LED's long. The strips are setup in groups of two where each group is driven by a single universe. Each group has a jumper on the ground and signal at the ends between pixel 75 and 76. Running 150 LED's per universe keeps me below the universe limit of 170. The web page for the LED's is below.
If you want to go bigger, you could use two of these. They have jumpers to set the universes to 15 different base universe addresses. I also have made a controller that will handle four times the number of lights and have a second one in stock. So if you wanted to do a sign 120x32 this single controller would support the sign. I have not made a terminal block adapter, but I could do one for your application if you are interested. Still working my web site, but you can look at the two controller boards.



