Sign controller
 
Notifications
Clear all

Sign controller

21 Posts
8 Users
0 Reactions
8,592 Views
Posts: 792
(@boarder3)
Noble Member
Joined: 19 years ago

i made a led sign last year out of pixel strings and it worked good just not good enough. What would the cost be to do a 120x32 sign with the leds? ANd what did you mount the leds on?


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago
boarder3 wrote:i made a led sign last year out of pixel strings and it worked good just not good enough. What would the cost be to do a 120x32 sign with the leds? ANd what did you mount the leds on?

I mounted mine on a wood backing with silicone adhesive. I cut dado groves into the wood for the strips to lay in. This was for an indoor installation.

Cost for 120x32 display depends on your choice for strings, etc, but I will give you an example.

So 60 LED/meter strip goes for about $10.25 through Ray's store, plus shipping: $20.50*32 $20 shipping = $696 in LED's
Power supply for 5Vdc is 0.06mA per LED or 230 amperes at 5Vdc: $20 * 4 = $42 shipping = $122
My single 32 universe controller $80 + $20 terminal block adapters = $100
Plus frame/enclosure

LED's
http://www.aliexpress.com/store/product/4m-DC5V-WS2812B-BLACK-PCB-led-pixel-srip-non-waterproof-60pcs-WS2812B-M-with-60pixels/701799_948310722.html

Power Supply
http://www.aliexpress.com/store/product/350W-Dual-Output-Switching-Power-Supply-88-264VAC-input-5V-350W-output-CE-and-ROHS-approved/701799_289599937.html


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago

At those prices I would try a LED flat screen TV first 🙂


Reply
Posts: 792
(@boarder3)
Noble Member
Joined: 19 years ago

Im debating on just buying a 50 inch plasma or led tv


Reply
Posts: 2
(@emishz)
New Member
Joined: 15 years ago

I like your design and would like one of those boards when they come in if you have a spare. Do the FPGA chips require firmware / programming?

Thanks for sharing!

Denny


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago
emishz wrote:I like your design and would like one of those boards when they come in if you have a spare. Do the FPGA chips require firmware / programming?

Thanks for sharing!

Denny

The boards should come in tomorrow. There is a serial flash chip on the board that needs to be programmed. Terasic sells an Altera programmer for $50 at Digikey, I bought mine off e-bay for $10 or so. Do you just want a spare board or do you want it stuffed and programmed?


Reply
Posts: 2
(@emishz)
New Member
Joined: 15 years ago

stuffed and programmed please!


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago

Well, I wanted to update my progress. I am currently waiting on a couple of parts that should arrive this week. So I will have tested boards, ready to ship the first of next week.

For my sign, I am basically done except for a piece of charcoal Plexiglas for the front. I will post pictures when I am completely done.


Reply
Posts: 238
Topic starter
(@ronp5683)
Reputable Member
Joined: 14 years ago
SignController

SignPower

I have completed my sign except for the front bezel. I am going to use grey Plexiglas.

I used four power supplies to drive the sign. I injected the power in the center of the strip. I used four power supplies at 20 amperes each, instead of one big power supply. So each power supply drives four 75 pixel strings. A large power supply to me is scary, 5Vdc at 80 amperes. I think you could weld with that. Also at 20 amperes, I figured I could skip the fuses. Each of the power supplies has an internal fuse, so I skipped the AC fuse in the case. All of the power supplies have their grounds connected.

The controller worked fine driving the LED's with lab power supplies, less noisy. I had some problems when I hooked up the power supplies from Ray or China. I also, made a ground loop, by connecting all of the grounds at the end of the sign. I don't recommend this for others. To keep the noise of my board, I connected the grounds on the front of the sign at the beginning of the strip. After looking at the data sheet for the pixels, I figured out 5V drive is better, so I built the adapter board shown. This converts the 3.3Vdc to 5.0Vdc output. I will have more comments on this on my web site in a day or so.


Reply
Keebler
Posts: 1691
(@keebler)
Noble Member
Joined: 18 years ago

Very Very nice 🙂


Reply
Page 2 / 3
Share: