MiniRen8/4
 
Notifications
Clear all

MiniRen8/4

130 Posts
29 Users
0 Reactions
50.4 K Views
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago

I really like the idea of the compact size of the 4 channel units, man that would sure work out well for some of my remote areas and roof top stuff. I could pop those babies in PVC pods and save a lot of time not running a bunch of power cords and it would be a whole lot
cleaner looking. I think you've got a good solution with the MiniRen8/4, very nice indeed. 😉


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago

dirknerkle

What about adding some sort of this in to your controller ?

http://www.hth.com/filelibrary/pdffiles/plm-24.pdf


Reply
dnesci
Posts: 563
(@dnesci)
Honorable Member
Joined: 19 years ago
christmas-light wrote:dirknerkle

What about adding some sort of this in to your controller ?

http://www.hth.com/filelibrary/pdffiles/plm-24.pdf

I see one problem with this is the maximum baud rate is 2400. We generally use 56,000. This would probably not work for our shows as we are switching at a fast pace.


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago
dnesci wrote:I see one problem with this is the maximum baud rate is 2400. We generally use 56,000. This would probably not work for our shows as we are switching at a fast pace.

Oh Sorry didn´t see that 😳


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago
dirknerkle wrote:Here's some eye candy for you to look over... I'm not going to say much about it yet, but this is a self-contained 8-channel wireless Renard module that's only 1.75 x 3.5" 😎

More later...

Looks Great! 1 question though. Dose that pin header contain the correct combination of pins to support in-circuit programming? I think it would be a great benefit to be able to program these without pulling the pic. Since by design they will be programed with start address firmware they would need re-flashed if they were moved around in the display as your display grows.

Tyler


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
dnesci wrote:I see one problem with this is the maximum baud rate is 2400.

It would make it a piece of cake for ten channels.:roll: Prolly would have been cool ten years ago, not so much any more.:(


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
tstraub wrote:Looks Great! 1 question though. Dose that pin header contain the correct combination of pins to support in-circuit programming? I think it would be a great benefit to be able to program these without pulling the pic. Since by design they will be programed with start address firmware they would need re-flashed if they were moved around in the display as your display grows.

Tyler

Some of the pins are there, but not all of them. That's a pretty good idea, Tyler since these things could wind up being mounted inside the guts of something else and hard to get to. I currently use an IC test clamp for my in-circuit stuff -- it's a squeeze clamp and you just clamp it onto the pins of the IC so for me, it doesn't matter if a board has an ICSP header or not. But I'll take a look at it. Good idea - thanks!


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
Great stuff, Dirk. That is just the kind of setup I need to control my fences at the front of the lot next year.

Looks like I'm going to have to look into the home etching thing, though. As if I didn't have enough to do already!

BTW: Are you on vacattion? Where are finding time to do all this stuff?


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago
IdunBenhad wrote:Hi:

... Are you on vacattion? Where are finding time to do all this stuff?

Dirk was clearly born with a silver spoon in his mouth and has never had to work a day in his life... Sorrry Dirk, secret is out!


Reply
griffixdc
Posts: 2512
(@griffixdc)
Famed Member
Joined: 16 years ago
kychristmas wrote:Dirk was clearly born with a silver spoon in his mouth and has never had to work a day in his life... Sorrry Dirk, secret is out!

wow that must be nice.....any ways i am getting interested in the home etching thing myself..... what are the main things i need to get me started....what program do you use to layout the circuitry.....is an inkjet printer ok to do the iron on transfers or do you have a better way of doing it....and whats the best solution for the acid. where do you buy the pcb board at a good price? Lots of questionsi figured i would ask someone that does it already.


Reply
Page 4 / 13
Share: