dmcole wrote:Erik:Better minds than mine have looked at your schematic and not said anything, so I'm a little worried that I don't understand your power supply circuit.
A traditional LM7805 circuit would have a big capacitor hanging off of Pin 1 (and, according to one of my friends, a decoupling cap there as well) and then two different caps -- usually a 10uf and a .01uf -- hanging off Pin 3. Maybe there's something here that I don't understand that wouldn't require all those caps.
Also: does the traditional Renard RJ45 connection come in on Pins 4-5? I know the DIYC DMX RJ45 is on Pins 1-2. You might also consider devoting some board real estate to a DMX out RJ45, which I think the Renardites might want as well.
Now: to get me some of them GECEs ...
Best o' luck.
\dmc
The datasheets for the 7805 usually show only a 0.1 uF cap on the output of the regulator. There are often additional caps used for decoupling, but these are required by the attached circuitry, not by the regulator itself. And the schematic does show two 0.1 uF caps on the output. In addition, the values shown on schematics (especially early schematic versions like this) are often place-holders, rather than the final value.
As far as the input side goes, again the data sheets usually show quite small values. The datasheet that I'm looking at shows 0.33 uF, which could usually fit in the same holes as the 0.1 uF that the OP shows. Again, at the board layout level, what matters is that there is a provision for a component, and it's not so important if the value on the schematic is not quite right. If you see much schematics with much larger values, those are usually there for purposes other than regulator stability or transient response.
For layout purposes I think that the schematic is OK wrt the regulator caps.
P. Short wrote:For layout purposes I think that the schematic is OK wrt the regulator caps.
Thanks Phil, the datasheet I have on the 7805 shows a .33 uF cap as well. I updated my schematic.
As the Renard guru, do you think the PIC15F688 should be able to handle this, or do you have another suggestion for a PIC?
Thanks,
Erik
dmcole wrote:Erik:Better minds than mine have looked at your schematic and not said anything, so I'm a little worried that I don't understand your power supply circuit.
A traditional LM7805 circuit would have a big capacitor hanging off of Pin 1 (and, according to one of my friends, a decoupling cap there as well) and then two different caps -- usually a 10uf and a .01uf -- hanging off Pin 3. Maybe there's something here that I don't understand that wouldn't require all those caps.
Also: does the traditional Renard RJ45 connection come in on Pins 4-5? I know the DIYC DMX RJ45 is on Pins 1-2. You might also consider devoting some board real estate to a DMX out RJ45, which I think the Renardites might want as well.
I will look into the DMX out. I see RPM's board mentioned in the thread has that, so I can follow that design. To me, it doesn't matter where the pins are, so I will defer to the community.
Thanks,
Erik
erm213 wrote:Thanks Phil, the datasheet I have on the 7805 shows a .33 uF cap as well. I updated my schematic.As the Renard guru, do you think the PIC15F688 should be able to handle this, or do you have another suggestion for a PIC?
Thanks,
Erik
I'm not sure what processor is supposed to do. My guess is that you want to receive data through the uart from some source (Vixen on a PC?), buffer it up, and then transmit it out somehow or other to the pixel strings. I'm guessing that you are planning on using the PIC16F688 uart for receiving data in either the Renard or DMX512 format, so that you will have to bit-bang data out to the pixels. I'm guessing that you are going to want to handle at least 128 pixels = 384 channels, so I would suggest using something like a PIC16F1825 instead of the PIC16F688. It has the same pinout as the PIC16F688, is cheaper, and has a lot more memory.
Take this with a grain of salt, though, because I'm not really sure what the task is yet.
P. Short wrote:I'm not sure what processor is supposed to do. My guess is that you want to receive data through the uart from some source (Vixen on a PC?), buffer it up, and then transmit it out somehow or other to the pixel strings. I'm guessing that you are planning on using the PIC16F688 uart for receiving data in either the Renard or DMX512 format, so that you will have to bit-bang data out to the pixels. I'm guessing that you are going to want to handle at least 128 pixels = 384 channels, so I would suggest using something like a PIC16F1825 instead of the PIC16F688. It has the same pinout as the PIC16F688, is cheaper, and has a lot more memory.Take this with a grain of salt, though, because I'm not really sure what the task is yet.
You nailed it, I want it to take DMX or Renard, and the convert it to the pixel protocol, so yes to the bit-banging once again. I will check out the PIC16F1825. I really do not need a lot of I/O pins. 128 would be the max pixels, as that seems to be the limitation before they run out of power.
I do have another question, if I was to try and support a pixel that needed a clock supply, should I use an external clock, or tap into the pics clock.
Thank you,
Erik
generally you bit bang the clock in phase with the data you sending out.
I've done a DMX -> Pixel board with CAT5 input/loop, but I used the ESTA DMX RJ45 pinout and added power to pins 4+5. (like PoE in a way)
Over at ACL we called it P-DMX. It only has two wires for V+ and 0V, but is pin compatible with a regular DMX over CAT5 / RJ45 system.
For the CPU, I used a PIC16F1934-I/PT but that's surface mount. I also used the inbuilt SPI hardware to drive the 2801 / 6803 pixels.
David_AVD wrote:I've done a DMX -> Pixel board with CAT5 input/loop, but I used the ESTA DMX RJ45 pinout and added power to pins 4+5. (like PoE in a way)Over at ACL we called it P-DMX. It only has two wires for V+ and 0V, but is pin compatible with a regular DMX over CAT5 / RJ45 system.
For the CPU, I used a PIC16F1934-I/PT but that's surface mount. I also used the inbuilt SPI hardware to drive the 2801 / 6803 pixels.
David, do you have a link I could check out the project? I have not done much PIC programming, do you think SPI would be the wayt o go here as well?
Thanks,
Erik
The project itself is not open source, but I have started documenting P-DMX in the ACL wiki.
Using the PIC's SPI hardware frees up a lot of processing time and should give more consistent operation if you have DMX, etc to deal with too.
David_AVD wrote:The project itself is not open source, but I have started documenting P-DMX in the ACL wiki.Using the PIC's SPI hardware frees up a lot of processing time and should give more consistent operation if you have DMX, etc to deal with too.
Thanks David, I will read up on it!
Erik
