Introducing the Pix...
 
Notifications
Clear all

Introducing the Pixel String Controller

25 Posts
8 Users
0 Reactions
12.5 K Views
erm213
Posts: 479
Topic starter
(@erm213)
Honorable Member
Joined: 16 years ago
[#15830]

Hello,

Here is my latest idea. This is a controller for pixel type strings, 2 in particular to start with, the GE Color Effects, and the TM18XX pixels. I chose those because I have those! 😀 The basic idea is both power and data will be delivered via cat 5. 3 pairs will deliver the power at 24 V DC. The last pair will have the data over RS485. It should support the Renard protocol, as well as DMX. I say should, because I have not started on the firmware yet. The plan is to start with the Renard DMX firmware, and modify it to work with the pixel strings (any help would be appreciated). There will be a firmware for each type of pixel string.

I know the E68x boards are out there that can control both of the proposed (and more) pixels. The E680 controllers are great for a centralized display, like a mega tree, where all of the pixel strings start pretty close to each other. This board is for a decentralized display, for example, I want to put flexible LED strips around the windows on my house. It would be cost prohibitive, and a waste of it's capabilities, to put a E68X controller on each window, or even pairs or windows where it would work out. this controller will provide the ability to have a decentralized pixel string where ever it is needed.

I am not familiar enough with the Renard protocol to know how many channels it is limited to, but I am pretty sure the limit will be the size of the string. GECE can only address 63 unique pixels per string. With DMX, it will be able to do 170 RGB pixels per string, but once again, the limit for a lot of the TM18XX is about 128 pixels per string, so that should not be an issue.

The controller can be built to support 5 V DC or 12 V DC strings, and supply up to 3A of power (using a LM2576-05 or LM2576-12). If the 12 VDC option is chosen, a 7805 regulator is added to supply 5 V DC power the RS485 chip and the pic. Right now, based on the schematic, it should cost about $12-$13 per controller for single at a quantity of one.

Any feedback on the schematic, or features would be appreciated.

Thanks,

Erik


24 Replies
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

JP1 connected wrong. Connect the 7805 input permanently to the 12V rail.
JP1:3 needs to go 12v only
Jp1:2 goes to SL1:1 only
finally if intend to add 2801 control you will need Clk and Data on SL1, not just data.

RPM has already done a similar unit ( albeit using a different u Controller). you may find his work useful to review
http://doityourselfchristmas.com/forums/showthread.php?15286-DMX-to-WS2801-Pixel-Bridge


Reply
erm213
Posts: 479
Topic starter
(@erm213)
Honorable Member
Joined: 16 years ago
Matt_Edwards wrote:JP1 connected wrong. Connect the 7805 input permanently to the 12V rail.
JP1:3 needs to go 12v only
Jp1:2 goes to SL1:1 only
finally if intend to add 2801 control you will need Clk and Data on SL1, not just data.

I don't want the 7805 permanently on the 12V rail, as there may not be a 12V rail. If you are going to use 5V pixels, you would put the LM2576T-005G, and the 7805 would not be required. In this case, you would put a shunt on pins 2-3 of JP1. If you want 12V pixels, use the LM2576T-012G, and put the shunt on pin 1-2 of JP1. The output of the LM2576 should always go to the pixels.

I had not thought of the 2801, as I don't have any, but its something to look into.

Matt_Edwards wrote:RPM has already done a similar unit ( albeit using a different u Controller). you may find his work useful to review
http://doityourselfchristmas.com/forums/showthread.php?15286-DMX-to-WS2801-Pixel-Bridge

Thanks, I will look at RPM's board.

Thanks for the comments,

Erik


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

There's jstjohnz's E680 and E681 pixel controllers as well which supports most of the pixels out there already. Not trying to dissuade you - just want to be sure you're aware of them.


Reply
erm213
Posts: 479
Topic starter
(@erm213)
Honorable Member
Joined: 16 years ago
budude wrote:There's jstjohnz's E680 and E681 pixel controllers as well which supports most of the pixels out there already. Not trying to dissuade you - just want to be sure you're aware of them.

Thanks budude, I am aware. I have 2 of the E680's, and will probably pick up a E681 when its ready. They are great boards, but a drawback is that you have to have the controller near the start of the pixel strings. That's great for a mega tree and some other structures. I want to put the flexible LED 1809 strips around my windows. The E68x is not really suitable for that as I need to span the entire house. This is intended for pixel strings that are more dispersed. I even thought about scaling down the design of the E68x, but I didn't need the horsepower of the Prop. If they had a cheaper version of the prop, that would make it easier!

Erik


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago
erm213 wrote:Thanks budude, I am aware. I have 2 of the E680's, and will probably pick up a E681 when its ready. They are great boards, but a drawback is that you have to have the controller near the start of the pixel strings. That's great for a mega tree and some other structures. I want to put the flexible LED 1809 strips around my windows. The E68x is not really suitable for that as I need to span the entire house. This is intended for pixel strings that are more dispersed. I even thought about scaling down the design of the E68x, but I didn't need the horsepower of the Prop. If they had a cheaper version of the prop, that would make it easier!

Erik

Erik
I am in sync with your reasoning totally. Having the ability to add a universe of Pixel control out in the garden is great. For example I am hoping to add a couple of pixel based shooting stars this year. Running these off DMX just make perfect sense.

(BTW sorry if my first post came across negative - never my intention for knock any one's design.)


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Yep - I echo Matt - you may want to update the first post to make it clear the intended purpose - it's perfectly clear to me now - full speed ahead!


Reply
erm213
Posts: 479
Topic starter
(@erm213)
Honorable Member
Joined: 16 years ago
Matt_Edwards wrote:(BTW sorry if my first post came across negative - never my intention for knock any one's design.)

It didn't. No worries!

Erik


Reply
erm213
Posts: 479
Topic starter
(@erm213)
Honorable Member
Joined: 16 years ago
budude wrote:Yep - I echo Matt - you may want to update the first post to make it clear the intended purpose - it's perfectly clear to me now - full speed ahead!

Updated, thanks for the suggestion.

Erik


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago

Erik:

Better minds than mine have looked at your schematic and not said anything, so I'm a little worried that I don't understand your power supply circuit.

A traditional LM7805 circuit would have a big capacitor hanging off of Pin 1 (and, according to one of my friends, a decoupling cap there as well) and then two different caps -- usually a 10uf and a .01uf -- hanging off Pin 3. Maybe there's something here that I don't understand that wouldn't require all those caps.

Also: does the traditional Renard RJ45 connection come in on Pins 4-5? I know the DIYC DMX RJ45 is on Pins 1-2. You might also consider devoting some board real estate to a DMX out RJ45, which I think the Renardites might want as well.

Now: to get me some of them GECEs ...

Best o' luck.

\dmc


Reply
Page 1 / 3
Share: