Good old fashioned ...
 
Notifications
Clear all

Good old fashioned RELAYS...

15 Posts
6 Users
0 Reactions
4,694 Views
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago
[#18614]

So I had a recollection that I had snagged a dozen (tubes) of small relays at some point in the past. (8+ yrs ago)
It occurred to me that I would like to use relays to control my ACL strobe lines, and I wondered if these might be put to use.
So I dug them out and tried to find relevant information about them.

Part Number: DSB2E-S-DC5V

Google search resulted in: the following PDF

From which I pulled this image:

DSB2E S DC5V

What I don't see is what kind of amperage I can expect this little device to handle.

I'm envisioning a board with 3 SSR's and one RELAY (RGB+Strobes).

Thoughts?


14 Replies
jrock64
Posts: 1099
(@jrock64)
Noble Member
Joined: 19 years ago

Doesn't it say 2 amp contacts in the title.:wink2:

Must be early.

Joel


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Make sure you wire the coil with the correct polarity (pin 1 is positive).
/mike


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago
jrock64 wrote:Doesn't it say 2 amp contacts in the title.:wink2:

Wow.. forest for the trees. Amazingly enough that 2A never jumped out at me.
Do you think that would be 1A per side then?


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago
n1ist wrote:Make sure you wire the coil with the correct polarity (pin 1 is positive).
/mike

Yes. I almost didn't notice the +/- in the image, but zoomed into the PDF after I saw the "polarized" word in the title.
LOL - three lines down from the line I didn't see (sigh).


Reply
EasyGo
Posts: 93
(@easygo)
Trusted Member
Joined: 16 years ago

And, notice that the coil power of 360 mW / 5 V = 72 mA of operating current ... :omg:


Reply
Posts: 123
(@randyn)
Estimable Member
Joined: 17 years ago

Andrew,

Those relays should be good up to 2 amps.

Randy


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Ahh.. and looking at the standard DCSSR opto, it can push only 50ma, so I would need a small transistor in there as well.
(and the diode to handle the inductive *stuff* :wink:)


Reply
EasyGo
Posts: 93
(@easygo)
Trusted Member
Joined: 16 years ago
LabRat wrote:Ahh.. and looking at the standard DCSSR opto, it can push only 50ma, so I would need a small transistor in there as well.
(and the diode to handle the inductive *stuff* :wink:)

Actually, the reason those are polarized is that they have the back-EMF-blocking diode already in the package, so they took care of that issue for you.

I used a bunch of DS2Exxx relays for some radio stuff once (no "B" in the part number so I assume the contacts weren't bifurcated). They are rated for 2 amps per contact. I experimented to find the lowest current the coils would reliably operate at, and then added a resistor to to set the coil operating current at some margin higher than that. It was 14 years ago that I did that, so I don't remember what coil current I settled on, but I do remember that it was quite a bit less than the rated current. I had several dozen of them in a matrix, and saw pretty quickly that power dissipation was going to get out of hand if I ran them at full power.

Cheers,
Jon


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Interesting, so it's looking like I can pretty much drop one of these into a DCSSR in place of the MOSFET.
The control line that normally goes from the opto to the mosfet, would now be going to the + terminal of the RELAY.

If it works, I can see a respin of the DCSSR in my future that would:
a. Have a 4 pin terminal block for the 3 mosfets (+5, and channels 1-3 dimmable)
b. Have a 2 pin connector connector for the relay (+5, channel 4 on/off)

Allowing for an RGB+strobe mini-tree.

Any interest in something like this by anyone else?


Reply
Page 1 / 2
Share: