Renard Based Wirele...
 
Notifications
Clear all

Renard Based Wireless Servo PCB

12 Posts
5 Users
0 Reactions
4,307 Views
gdyrdave
Posts: 916
Topic starter
(@gdyrdave)
Noble Member
Joined: 16 years ago
[#18625]

I have been playing withe the Renard Servo controller and came up with this PCB. It is a Ren Servo mixed with Dirknerkle's XBLSD board. I reduced the size to get it mini board constraints to get the prototype costs down. I would like ctmal and Dirks comments on this before i finalize and send off for a prototype. Also wondering which PC house they go to for the lowest price (Hey Dirk,where do you get your boards made?) I left the zero crossing circuits in there too. May use this for an SSR also. Comments and opinions welcomed. This is my first attempt to at least do a PC board. I used the designs of Dirks and Ctmal so I dont take credit for anything. My main thought was to use this for animated skulls or angels for this years display ( my first). I also want to thank everybody who has helped me fullfill my dream of this lighting concept. It all started years ago when I saw the Wizards of Winter on the internet. Thanks guys and gals!!!

Dave


11 Replies
Posts: 352
(@maffeirw)
Reputable Member
Joined: 19 years ago

I love the idea of a wireless Servo Controller. I really can't comment on the electronics of the board but I don't see an RJ45 output to daisy chain additional controllers. I'm not sure if it's a big deal to anyone else but I hope to run a skull quartet for Halloween and would like to wirelessly connect to the first skull then daisy chain to the rest of them.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Hey, Dave!

Nice job!

Couple thoughts.... since I'm not a servo user... If there's any chance of back-flow current from your servos, you might consider some diode protection between the set of 8 header pins (JP1) and your output pins. Remember, those outputs are coming right off the PIC. The purposes of the transistors in the LSD board were two-fold: obviously #1 is to boost the output current but secondly, they serve as a sort of first line of defense against any back-current to the PIC. (I used the same concept to make a relay board -- the transistors boosted the output enough to drive the relays, but I also added diode protection on that, too.)

You're right that it can certainly be used to control SSRs -- that's essentially what a Ren64 does -- PIC outputs to RJ45 jacks to the SSRs.

For prototyping, you could get 4 of those boards from ExpressPCB for about $95 using their standard service (no silk screen, no solder mask), and if you ordered them today (Saturday) you'd have them by next Thursday. Four with solder mask and silk-screen would run you about $175 but you'd have them by Thursday, too. I'd recommend the latter and granted, $175 isn't cheap, but with that back-plane, it'll be a lot friendlier to solder.

There's a cost to prototyping using ExpressPCB 😆 But they deliver a very, very good product extremely quickly.


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Can you post a picture, versus the PCB file? I'd love to see what you are working on, as I've been spinning something very similar (detailed in my blog). I'm all "eagle" based, so can't see your file. I've got a set of my board being proto-typed right now. Seeedstudio is certainly cheaper, but also somewhat slower.


Reply
gdyrdave
Posts: 916
Topic starter
(@gdyrdave)
Noble Member
Joined: 16 years ago

Dirk, No chance of back flow current due to the signal to the servo is a pulse .5 to 2.5 ms and a current level dependant upon the servo... normally around 10ma if that. Trying to figure out a way to put the PCB in a PDF format. Not sure. Some one with Express PCB experience may help so I can post for LabRat.Like I said its my first time so be gentle...LOL

Dave

The better half said dont be...ROFLMAO


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
gdyrdave wrote:Dirk, No chance of back flow current due to the signal to the servo is a pulse .5 to 2.5 ms and a current level dependant upon the servo... normally around 10ma if that. Trying to figure out a way to put the PCB in a PDF format. Not sure. Some one with Express PCB experience may help so I can post for LabRat.Like I said its my first time so be gentle...LOL

Dave

The better half said dont be...ROFLMAO

You can make a JPEG of it pretty easily -- Open Paint, then open the ExpressPCB. Press ALT-PrintScreen, then go to Paint and click Edit - PASTE. Then you can use SAVE-AS to save it as a JPG and attach it to a posting. Piece of cake.


Reply
gdyrdave
Posts: 916
Topic starter
(@gdyrdave)
Noble Member
Joined: 16 years ago

Thanks Dave... I will try that.

Dave


Reply
gdyrdave
Posts: 916
Topic starter
(@gdyrdave)
Noble Member
Joined: 16 years ago

Here ya go LR.. Best I could do at this time.

Dave

RenServoXB

Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Thanks for taking the time to make this. If this is only to control servo's, what's the need/function of the H11AA1?


Reply
gdyrdave
Posts: 916
Topic starter
(@gdyrdave)
Noble Member
Joined: 16 years ago

Just in case you might want to run ssr's off of this. When I get more versed into PCB design it will probably be removed. It would be nice to have the Ren addressing scheme into the pics but that may be a Phil Short project. Also would love to have limits in the pic to reduce the chance of bottoming out the servos and breaking a gear. Time will tell. Thanks Lab for your input... You too Dirk..... You were my inspiration anyway... You da man!!!! Of course Ctmal for starting the servo thing all together.

Dave


Reply
Page 1 / 2
Share: