FPP PB16 Pixel Cont...
 
Notifications
Clear all

FPP PB16 Pixel Controller

630 Posts
62 Users
6 Reactions
389.5 K Views
Posts: 629
(@dkulp)
Honorable Member
Joined: 14 years ago
Cmndr Brain wrote:
Last, does the speed of the EEProm make a difference? I see that Digikey is out of stock and the only ones I can seem to find are 400khz whereas the Digikey part number referenced in the bom is a 1Mhz

The PocketBeagle and BBB max the i2c bus at 400khz. Thus, using a 400khz eeprom is perfectly fine. When I first put eeproms on my boards, I was hoping to eventually have newer beagles (like the Beaglebone AI) that have a 1mhz i2c bus, but that really hasn't happened yet.


Reply
Posts: 5
(@kpken)
Active Member
Joined: 16 years ago

I created my own version based on this great design (And also Dan's boards), I needed one that is small and compact with a lot of Diff ports and only a couple local ports and all SMT.
It turned out really good and got it in purple from JLC.
The thing I have noticed that the 26C31 IC's get quite warm, almost to hot to touch when just powered up, is this normal for these?
I have never used this Diff IC before (Mostly Maxim ones before), and they also stay warm when all 4 outs are active to the receiver driving pixels, and all 4 work as expected.
I have checked that there is no shorts and cleaned the board a few more times just in case.


Reply
Posts: 87
Topic starter
(@scooter-seh)
Trusted Member
Joined: 12 years ago
kpken wrote:I created my own version based on this great design (And also Dan's boards), I needed one that is small and compact with a lot of Diff ports and only a couple local ports and all SMT.
It turned out really good and got it in purple from JLC.
The thing I have noticed that the 26C31 IC's get quite warm, almost to hot to touch when just powered up, is this normal for these?
I have never used this Diff IC before (Mostly Maxim ones before), and they also stay warm when all 4 outs are active to the receiver driving pixels, and all 4 work as expected.
I have checked that there is no shorts and cleaned the board a few more times just in case.

I found with the AM26C31 when you put the two enable pins, pin 4 and 12 high and low the IC gets hot. It must be sourcing current through the IC. I found if you just pull pins 4 and 12 low it will work fine.

2021 11 11 20h41 50

Reply
Posts: 79
(@bobsmith)
Trusted Member
Joined: 11 years ago

On a somewhat related note to these boards, does anyone know how a "Smart Differential" receiver actually works? I can find info on how they're setup, but not anything on how the protocol actually works. Is the smart receiver programmed somehow to know what channel ranges it should take from the stream? Or is some switching signal sent in the datastream?

Does it send a "receiver A" command, then like 50 pixels (or however many you have configured) worth of data, then a "receiver B" command, and then X pixels of data?
Or does it send raw data, and the receivers know how many channels they're setup for each apriori?

I don't really need this info for anything pressing, but I'm curious how the protocol actually works, and it seems like it's super secret info (that anyone with an oscilloscope and 10 minutes could figure out anyway). The only readily available info I can find is "you can't mix smart and dumb differential receivers, termination switches, and how to select receiver A B and C or old-style dumb mode" and mostly in 30 to 45 minute video format to tell me 30 seconds worth of info. I also see in the latest FPP firmware that there's a smart differential V2 now that supports 6 "smart" receivers instead of 3.


Reply
Posts: 5
(@kpken)
Active Member
Joined: 16 years ago

Thanks Scott, that is very helpful, 🙂
I set it up identical to your AM26C31 with pin 4 and 12 (Enable pins) to Gnd, I will take a look at the datasheet again and see if there is something I can test.
I think you are right that it is sourcing current some where, just need to find it, and why it is doing it on all 6 of them.
I will also recheck the one that is connected to the 4 single ports w/ power is also getting warm (little harder, its under the OLED).
Attached is SCH/PCB snip of one of the ports.
Please let me know if you have any other ideas, thanks.

Update: I checked that there is no pins to Gnd that shouldn't be, dif outputs Ohm good with term resistor, no shorts to Gnd.

SCH Capture
PCB Capture

Reply
Page 85 / 126
Share: