That should work. I also made a Pi Breakout with a 40 pin Expansion header. This one does require separate power to the Pi in most cases. Pi 2 Expansion Link
Glycerine wrote:In reference to the "PI Zero to PB16 adapter" ( https://github.com/computergeek1507/PB_16/tree/master/PB16_2_PI )...The raspberry pi zero has the same pinout as the raspberry pi 3 and 4, correct? So, if I wanted to use this adapter with a pi 4 instead of a zero, I could do so by using a ribbon cable between the pi 4 and the adapter, right?
scooter_seh wrote:That should work. I also made a Pi Breakout with a 40 pin Expansion header. This one does require separate power to the Pi in most cases. Pi 2 Expansion Link
Oh, nice! Thank you.
I've built 3 PB16's and am really just starting to put up my pixels. I am having data issues with them on my runs where a cheap little pixel tester is not. I needed to put in an f amp after 112 pixels and 10' of 3 core wire. Is this normal or is it possible I messed something up? Controllers connected directly into the first strand of 112 pixels to 10'of wire to my door outline of 105 pixels, but only the first 8-10 work fine with no data issues. I put the f amp on the output side of the first window outline and all is ok. I've spent hours trying to figure out what's going on with no luck other than leaving the f amp in. It just doesn't seem like I should need it. Thoughts? Ive swapped in a second PB16 and no change.Is it a possibility I've built 2 wrong to where they're not getting good data? I've swapped in a similar 5v regulator since the original was not available but I don't know if that could be causing an issue
Shawnd wrote:Controllers connected directly into the first strand of 112 pixels to 10'of wire to my door outline of 105 pixels, but only the first 8-10 work fine with no data issues. I put the f amp on the output side of the first window outline and all is ok.
A diagram would be helpful to help us understand exactly how your system is wired up. From your description, it sounds like the controller is working fine. If the first pixel connected to the controller is working fine, then the controller connection is working. The way pixels work is each pixel takes its' input, strips off the data it uses for itself and regenerates the signal to the output. So, everything after the first pixel, relies of the output of the previous pixel and not the controller. So, the second pixel relies on the output of the first pixel. In your case, the first pixel of the second prop (door outline) relies on the last pixel of the first prop which has 10' of wire between the two pixels. So, my estimation is the problem is related to this connection. The F amp has a better output driver circuit than a standard pixel output and therefore is capable of achieving longer distances. So, in your situation, inserting the F amp is overcoming the problem.
The root cause is likely related to your power and ground connections. As the current increases the voltage drop on the wires increases. As the voltages drop increases, the voltage at the pixel is reduced which reduces the pixel's ability to reject noise. How many pixels in total are connected to this port? Are you providing injection anywhere along the strings connected to the port? If you can provide some additional information about how you have wired your power it may provide some clues.
The simple solution is just keep using the F amp but this could be masking a bigger problem related to your power distribution. For safety reasons, it is important that you properly wire your pixels.
What size resistor packs are you using? I use 33 ohms on my controllers and I can get 30ft to the first pixel. I also use 18ga stranded wire for all my wiring.
Thanks,
Scott
Shawnd wrote:I've built 3 PB16's and am really just starting to put up my pixels. I am having data issues with them on my runs where a cheap little pixel tester is not. I needed to put in an f amp after 112 pixels and 10' of 3 core wire. Is this normal or is it possible I messed something up? Controllers connected directly into the first strand of 112 pixels to 10'of wire to my door outline of 105 pixels, but only the first 8-10 work fine with no data issues. I put the f amp on the output side of the first window outline and all is ok. I've spent hours trying to figure out what's going on with no luck other than leaving the f amp in. It just doesn't seem like I should need it. Thoughts? Ive swapped in a second PB16 and no change.Is it a possibility I've built 2 wrong to where they're not getting good data? I've swapped in a similar 5v regulator since the original was not available but I don't know if that could be causing an issue
