FPP PB16 Pixel Cont...
 
Notifications
Clear all

FPP PB16 Pixel Controller

630 Posts
62 Users
6 Reactions
389.6 K Views
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Very good. Yes, please keep the Through Hole board free of smd!

scooter_seh wrote:I looked at adding the LM2576S-ADJ from your design but it is so big, I cannot fit it, the inductor, and capacitor in the current space. I would have it widen the PCB. I started experiencing with the AP1509 regulator, which is available at JLC but not anywhere in the States. I would like to keep the OG PB16v1 all through hole, which makes using a on-board regulator petty much impossible. For the surface mount boards, I am open to it.

Reply
Posts: 79
(@bobsmith)
Trusted Member
Joined: 11 years ago
scooter_seh wrote:I looked at adding the LM2576S-ADJ from your design but it is so big, I cannot fit it, the inductor, and capacitor in the current space. I would have it widen the PCB. I started experiencing with the AP1509 regulator, which is available at JLC but not anywhere in the States. I would like to keep the OG PB16v1 all through hole, which makes using a on-board regulator petty much impossible. For the surface mount boards, I am open to it.

Yeah, there isn't a whole lot of wasted (or free) space on the through-hole board at all. Just from looking at it, the only way I could see it working is if you moved the renard/DMX switch to above the renard/DMX jack, shifted the whole beaglebone down (to clear the expansion connector) and to the left a bit, then there might be space for it in it's current place. But that's just looking physically - I didn't actually try it in Kicad or anything - it might cause big problems with trace routing or something.


Reply
rayhjr
Posts: 972
(@rayhjr)
Noble Member
Joined: 12 years ago
algerdes wrote:Please post any findings you come across. Very interested.

I did some limited testing today. I have 240 meters or 787 feet of 24awg stranded cat6 from Monoprice. It is the longest piece of cat5,6 wire I have. I left it in the box coiled up and put connectors on either end of the wire. Connected one end to Diff. board and the other end to the Receiver board and ran 100 pixels with no problem. FPP Test and a Sequence ran fine. I hope to do more test in the days to come. I also want to see how far I can get off PB16 and BB16 to first Pixel.
Hope Everyone has a Wonderful Labor Day Weekend!!


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Excellent test reporting.
I look forward to hearing your your 'first pixel' testing!

rayhjr wrote:I did some limited testing today. I have 240 meters or 787 feet of 24awg stranded cat6 from Monoprice. It is the longest piece of cat5,6 wire I have. I left it in the box coiled up and put connectors on either end of the wire. Connected one end to Diff. board and the other end to the Receiver board and ran 100 pixels with no problem. FPP Test and a Sequence ran fine. I hope to do more test in the days to come. I also want to see how far I can get off PB16 and BB16 to first Pixel.
Hope Everyone has a Wonderful Labor Day Weekend!!

Reply
Posts: 12
(@shawnd)
Active Member
Joined: 5 years ago

Hello everyone,
I have built 3 of the standard PB16 controllers with the pocketbeagle. Is there a good add on fm transmitter for this controller similar to the kulp transmitter? I have went page by page and have not seen any references to this. I am new to pixels and controllers so please forgive me if this is a silly question
Thanks


Reply
Page 106 / 126
Share: