FAST troubleshootin...
 
Notifications
Clear all

FAST troubleshooting

38 Posts
12 Users
0 Reactions
10.9 K Views
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Ah HA, I was NOT crazy (this time)


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago
jklingert wrote:The best way to remove them is to cut the four leads off on the device side as close to the body of the LED as you can. Then remove one lead at a time from the pcb.

Thanks ... wasn't able to make reuse of the LED but finally did get it out and a new one replaced put in the correct way.

rca wrote:Just for grins, try the other firmware 20110804.asm and see if it works.

Thanks. Tried it. Nada.

CaptKirk wrote:You could also try the HEX files that Cory provided in the FAST dev thread- I know they work!!

Thanks. Tried them. Nothing.

mschell wrote:Cory posted in another thread that he found an error in the random firmware source with exactly the behavior you might have seen if not for the bad LED. Suggest you recheck the wiki or wherever he posted the files...

Found the new HEX files -- both the revised random and the new diagnostic -- built them with MPLAB, uploaded the HEX and still get nothing.

ErnieHorning wrote:You need to figure this out. There’s nothing you could program into flash that’s going to give you one volt on the power supply.

Did you use a socket? If so, did you check the power pins on the bottom? How about without a micro?

Yes, used a socket. So, I've had the chip both in and out. When it's out, the voltage is a nice 5.03; when it's in, it's .94 measured either on the top of the chip or on the underside of the board.

So, I think this is the main problem -- could it be the socket itself? Maybe the cap? There aren't a lot of places where this thing could go wrong.

I may just build up another set and see what happens with those.

Thanks.

\dmc


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Hate to ask.. PIN 1 orientation??

If there's 5v difference without the chip.. and it's 0.95v *with* the chip.. there's something seriously amiss with the chip. No?
What's your power supply? Could you be trying to draw too much current and thus it's "browning out" ?? (I dunno.. kind of grasping at straws here)


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Expanding upon LabRat's thoughts, did you mount the socket on the correct side of the board?

And, it is a 5V DC power supply, correct?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Side of the board?!? dang.. not sure I would have ever considered *that*. Well done for thinking outside the box!


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago
LabRat wrote:Hate to ask.. PIN 1 orientation??

If there's 5v difference without the chip.. and it's 0.95v *with* the chip.. there's something seriously amiss with the chip. No?
What's your power supply? Could you be trying to draw too much current and thus it's "browning out" ?? (I dunno.. kind of grasping at straws here)

Pin 1 oriented correctly. With the board oriented so that you can read the silk-screens, the notch on the end of the chip goes up. I have twice pulled a fresh 16f out of the tube and programmed it and put them into the board. All for naught. FWIW, even after having been put into the board and run for a while, I have taken the chips back to the programmer and the programmer says they are fine.

CaptKirk wrote:Expanding upon LabRat's thoughts, did you mount the socket on the correct side of the board?

And, it is a 5V DC power supply, correct?

Again, the socket is on the side of the board with the silk screen.

I am getting a nice, sold 5.03v DC out of a supply I built out of a 7805 and some caps, driven by an ATX turned into a provider of 12v DC.

LabRat wrote:Side of the board?!? dang.. not sure I would have ever considered *that*. Well done for thinking outside the box!

But, a little further than necessary 😉 ...

\dmc


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

With the chip removed, can you do a continuity test between +5 and each of the other pins?
(trying to think under what conditions could we end up preventing reading the 5v differential)


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

how about a close up photo of both sides of the board?


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Can you find another 5V source to test?

Is the 12V drooping going into the 7805 when the 7805 is putting out the .95v?

Can you do a amp draw test on the output of the 7805 to see if you are exceeding the 1amp or so a 7805 can put out?

A short between pin 14 and pin 13 certainly could cause this.


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago

Update: There were, of course, multiple problems:

*If you went through this entire post, you'll note that I installed one of the LEDs backwards.

*Also, I misread the Wiki's description of how to wire the controller board to the first LED board ... I had it backwards, with the negatives in the right row of the first LED board and the positives in the left row. When I reversed those, it worked. I have updated the wiki with slightly better wording and included a wiring diagram that should be pretty clear.

*There is also a problem with the five-volt power supply. I'm not 100 percent certain what it is, but when I connect the FAST with two 3v batteries in series, it works.

Thanks to all who weighed in.

\dmc


Reply
Page 2 / 4
Share: