FAST troubleshootin...
 
Notifications
Clear all

FAST troubleshooting

38 Posts
12 Users
0 Reactions
10.9 K Views
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago
[#16356]

OK, this board is too simple for me 😉 ...

From the coop buy, I built up three LED boards and a controller, changed the number of LEDs in the 20110813 ASM file to 21, built the code with MPLAB 8.46 and wrote the resulting HEX file to the 16f1688 with my trusty JDM programmer and PICPgm. Wrote the HEX a couple of times, verified it. All seemed fine.

Apply 5v DC to the controller and nada. When I check with the meter directly on top of Pins 1 and 14 of the 16f, I see only .95 volts. Did continuity checks from the power feed to the pins 1 and 14 on the 16f1688 and everything appears to be wired correctly.

Have checked the individual LEDs after they were soldered into the boards by applying 3v to the backside and they all appear to be working. (Interesting note: when the 3v is applied to some LEDs -- not all -- other LEDs in the segment will flash off-and-on.)

And now, I'm stumped.

Other places to check with the meter? Other things to try?

Thanks.

\dmc


37 Replies
chelmuth
Posts: 1077
(@chelmuth)
Noble Member
Joined: 16 years ago

Sounds like there is a short somewhere.. possibly and LED in wrong.. or a brigded solder joint. as this would short the outputs. Photos?


Reply
Posts: 277
 rca
(@rca)
Reputable Member
Joined: 18 years ago

Just for grins, try the other firmware 20110804.asm and see if it works. I couldn't get the 20110813 firmware to work on mine last week either, but the 20110804 works great. I just haven't had a chance to get back to it to troubleshoot yet.

Ron


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

You could also try the HEX files that Cory provided in the FAST dev thread- I know they work!!


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
dmcole wrote:When I check with the meter directly on top of Pins 1 and 14 of the 16f, I see only .95 volts.

You need to figure this out. There’s nothing you could program into flash that’s going to give you one volt on the power supply.

Did you use a socket? If so, did you check the power pins on the bottom? How about without a micro?


Reply
Posts: 406
(@jboyles7)
Honorable Member
Joined: 17 years ago

I was tinkering with the FAST firmware last night to find that when I changed the number of LEDS to anything but 56 (21 and 7) it failed. I have the random firmware, and have not yet stepped through the code to find out why. This does not explain the power issue you noted above, but you could have 2 issues.


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago

Hey DMC, this might be a dumb question but do you get 5V from your power supply when it is NOT attached, and have you verified the polarity of the power to the chip?


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago
chelmuth wrote:Sounds like there is a short somewhere.. possibly and LED in wrong.. or a brigded solder joint. as this would short the outputs. Photos?

A double-check of the LED positions finds one oriented incorrectly. A few minutes of trying to desolder it left me with a burnt finger and a still-wrongly oriented LED. I need to go back to work, so probably won't finish this until tomorrow.

I will also seek out Cory's HEX files ...

\dmc


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

The best way to remove them is to cut the four leads off on the device side as close to the body of the LED as you can. Then remove one lead at a time from the pcb.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

Cory posted in another thread that he found an error in the random firmware source with exactly the behavior you might have seen if not for the bad LED. Suggest you recheck the wiki or wherever he posted the files...


Reply
Page 1 / 4
Share: