Dead man walkin
 
Notifications
Clear all

Dead man walkin

16 Posts
5 Users
0 Reactions
6,795 Views
Posts: 2630
(@dynamoben)
Famed Member
Joined: 19 years ago

If you aren't a PIC person the most basic way to pull this off would be either a Basic Stamp, EFX-TEK board, PicAXE, or Parallax Propeller. Any of these product could easily do what you are asking, its really a matter of cost (your time vs product cost).

In regards to powering the LEDs you can skip the relays for the LEDs largely because you don't need them and you can't dim each "foot." Take a look at the ULN2803/ULN2003. Both will allow you to drive the LEDs, or anything else for that matter.

Also the EFX-TEK forum has some cool examples of how to interface things like this with code examples that will work with any basic stamp.

BTW Last year I was going to build my own prop controller but it never made it off my bench.


Reply
DIY Guy
Posts: 542
(@diy-guy)
Honorable Member
Joined: 17 years ago

But what I think you are saying is build it without a processor, using timers. Interesting. Maybe use potentiometers to vary some of the timing. Would definitely be less expensive.


Reply
Posts: 150
Topic starter
(@sparkey)
Estimable Member
Joined: 19 years ago

Hi there, first off thanks for your input on this subject. I do appreciate hearing other folks ideas so I get a point of view all the way around the problem.

As this is the DIY site so yes, I'd like to make it myself. Not only is this the fun way but it is how I learn. So no, I do not want to buy something I want to enjoy this new hobby I have found. Again I appreciate the input, so don't take anything bad away from my reply, but for me it would be more fun spending my time on the project than spending the money. Also, if I get the darn thing to work I get neighborhood bragging rights!! WOO-WOO!

As to the LEDs you misunderstand what I had in mind. I wrote that the LEDs and relays were independent of each other. There will be a total of 20 LEDs, 2 sets of 10, to do the walking. And there will be 2 relays to do effects if you want them. I understand that you cannot technically "dim" a LED, it is a diode. But you can pulse the electricity to get that effect.
And even if the LEDs don't dim this prop is still a cool idea to me.

Thank you for jumping in on this. I hope to hear more from you.
Sparkey

DynamoBen wrote:If you aren't a PIC person the most basic way to pull this off would be either a Basic Stamp, EFX-TEK board, PicAXE, or Parallax Propeller. Any of these product could easily do what you are asking, its really a matter of cost (your time vs product cost).

In regards to powering the LEDs you can skip the relays for the LEDs largely because you don't need them and you can't dim each "foot." Take a look at the ULN2803/ULN2003. Both will allow you to drive the LEDs, or anything else for that matter.

Also the EFX-TEK forum has some cool examples of how to interface things like this with code examples that will work with any basic stamp.

BTW Last year I was going to build my own prop controller but it never made it off my bench.


Reply
Posts: 150
Topic starter
(@sparkey)
Estimable Member
Joined: 19 years ago

I have two thoughts about this. (1) the original idea was some sort of; timers, sequencers, potentiometers and associated hardware that could be adjusted by the POTS and TRIMMERS. (I don't know enough to do any of it though.) (2) the second idea, after deciding I wanted to build a REN64-XC, was could this thing be programmed to run with a PIC chip? (I don't know enough to do any of that either.) This is because I will need to get some PIC chips and a programmer for the REN64-XC real soon so... why not learn some more about the PIC and try it?

Right now this whole thing is a thought exercise and brain storming.

No disrespect to anyone but here is my thought process: I saw a device I liked but it did not do everything I wanted and I wanted to build it myself. I don't have a problem spending some money but this is supposed to be a fun hobby for an amateur like me. There is no where near as much fun if I just kind of pull something out of a box and plug it in. I found that out building my first GRINCH controller - what a blast to see something I made work. And you have no idea how happy I was to have friends and neighbors come over and ask me "how'd you do that" or say "man that's cool".

Thank you for jumping in on this. I hope to hear more from you.
Sparkey

DIY Guy wrote:But what I think you are saying is build it without a processor, using timers. Interesting. Maybe use potentiometers to vary some of the timing. Would definitely be less expensive.

Reply
Posts: 859
(@smartalec)
Prominent Member
Joined: 17 years ago

have you even thought of something realy easy.
a 4017 counter ic , thats 10 outputs. an a 555 counter ic to pulse the 4017 as to the speed.
there loads of examples if you put them in google search.

My first display 5yrs ago, i had 5x 4017 counter ic's connected to transistors to handle the extra current i was drawing, an a 555 to pulse each of the 4017 counters.

is this the track your thinking of?
alec.


Reply
Page 2 / 4
Share: