I would like to ask for some help building a controller. I know this is the CHRISTMAS
forum but there is a smattering of Halloween also, so.... drum roll... here goes nuttin
Any help making this dream come true would be appreciated.
A quick note, I am not an engineer or an electrician but I can follow a clear plan and
run a soldering iron. So please keep it on the lower end of technical talk.
BIG thanks in advance to any and all who want to jump in and help.
SPARKEY PROJECT: "DEAD MAN WALKIN"
(The original idea is not mine. I have based this off a prop called GHOSTEPS.
The modifications {activation, relays, delays and adjustable variables} are my idea.
As well as the concept on how I will use it.)
I'm looking for help to build a low voltage (5-24vdc) control board that allows you
to run a sequence of 20 LEDs that will fade from on to off with a slight delay
between each LED and activate two relays.
The public will see: what appears to be pirate boots walking through my
grave yard (L1-10) stopping in front of a ships bell. The bell rings (R1). Then
the pirate boots walk over to the grave yard gate (L11-20). A voice chip starts
(R2) and screams "BLASTED LAND LUBBERS LOCKED ME GATE!" End sequence.
I will use a Lexin outline of a boot with an LED inserted in the heel
that will "glow" with the LED - no "body" to be seen. SPOOKEY!
Hence I must have a 1,2 pattern (like walking).
1. I want to start the sequence by either a sensor (PIR, etc.) and/or switch.
My grave yard will have a fence so if a kid walks up to it, PIR activation.
I also want to run wire to a switch at my door so I can start it if I want.
2. The device should allow you to adjust the time interval from one LED to the next.
3. When started the entire sequence is latched on and must complete before it can start again.
4. There will be an adjustable time delay, 1-5 min, before the sequence can repeat,
to prevent fast and constant runs.
5. The LEDs will not be on the board, they will be attached to wires so I can logically
place the components where I want them.
THOUGHT PROCESS:
a) Activation (turn on), it runs to the end no matter what you do to sensor/switch.
b) L1 fades on (adjustable delay before next light comes on) then
c) L2 fades on (adjustable delay is the same for L1) then
d) L1 fades off (adjustable delay is the same for L1)
e) when L1 is off L3 fades on...
f) when the last output stops the unit stops until re-activated by the PIR or switch.
g) the run time interval for LEDs 1-10 and 12-21 are set by variable X
h) Run sequence = L01-10, R1, L12-21, R2
i) the run time interval for R1 & R2 is independent of the others and set by variable Y
j) one more time delay to keep the unit off for variable Z before it will run again.
I would like to buy one of those Radio Shack boards and just solder the
back side wires together with jumper wire to make it quick and dirty.
Maybe I'd try out an etchant but I've not had much luck with the iron on
track transfer paper so far.
+-------------------------------------------------------+
|..............................................TERMINALS 01-10........|
|....GUTS...................................................................|
|....GUTS.............ADJ-X................................R1 - T11..|
|....GUTS.............ADJ-Y..............................................|
|....GUTS.............ADJ-Z................................R2 - T22..|
|....GUTS...................................................................|
|....PWR.TERM............................TERMINALS 12-21........|
+-------------------------------------------------------+
Finally the device should run off a battery or wall xformer. Another
terminal here instead of a jack so one could run anything one wants. Even
put a jack on wires to the terminal but terminals offer the most freedom.
I have several power supplies, computer and other, but the voltages I
would like to be are: 5VDC, 7VDC, 12VDC, 20VDC or 24VDC as that is what I have.
So:
OBJECT.......L...L...L...L..L...L...L...L..L...L...R...L...L..L...L...L...L..L...L...L...L...R
OUTPUT#....01.02.03.04.05.06.07.08.09.10.11.12.13.14.15.16.17.18.19.20.21.22..END
VARIABLE....X...X...X..X..X..X..X...X..X...X...Y..X...X..X..X..X...X...X...X..X..X..Y...Z
(1) the unit will have the ability to take 10 steps at a set speed (X)
(2) on output 11 I'd like to latch a relay: I've included the link for you to look at
voltage & power requirements of a small relay I thought of.
Magnecraft # W117SIP-6. S.P.S.T., Normally-open, reed relay. 5Vdc, 500 Ohm coil w/ clamping diode. Rated 10VA, 0.5A switching and can carry up to 1.5 Amps. Four in-line pins, 0.2" between pins. Switching voltages are 120VAC or 200VDC.
so #11 would need to be an adjustable time (Y). say I wanted the relay to stay latched for 3-5
seconds I could dial it in.
(3) then when output 11 finishes 12-21 run their course at the starting speed (X)
(4) on output 22 I'd like the ability to latch a second relay same as R1
(5) the unit stops when output 22 is done for (Z) seconds (1 to 5 minutes)
Well, that says a lot. I hope I have been clear on what I'm trying to do.
Any thoughts to help me build this monster?
Thanks for looking at it if nothing else.
Sparkey
I think you could put this together with a board from efx-tek and a board from cowlacious.
That being said, I am all in for a new board. One of the problems with the efx-tek board is that it can't drive much current without add-on boards.
The prop-2 is steep at $99. I have a prop-1 and for sure it is a great little board, and the support at efx is top-notch; well worth the price of admission.
However, the basic stamp 2 module is gonna run $50. The up side is that you can easily write your own programs for it.
There might be cheaper alternatives, idk.
A ren24lv and some creative sequencing with vixen should be able to handle it. Vixen can use triggers and can play the audio bite and you can adjust the timming to get everything in sinc.
True. I suppose the question of the day is whether this board is proposed to be connected to a computer, or is it stand-alone.
My original idea is this will be a self contained unit, no computer required.
(This will also make it easier to integrate into a Halloween setup, well hidden.)
That is why I would like the adjustable variables on the board.
Possibly three 555 timers and POTS for variables X, Y, and Z?
The main power in will be enough to run the LED lights and activate the relays.
What ever one wishes to run via the relay is the users problem to establish.
As long as the relay goes on/off the capability is "there" to use was my thought.
If one does not want to use the relay set the time value to 0 and it gets skipped.
Note: It was from the relays I intended to; (1) turn on a small motor to ring a bell
and (2) turn on a digital voice recorder, to play a sound clip through a speaker.
I have just ordered parts for my first REN64-XC so my thoughts for this Halloween
board came from here: use the PIC micro-controller(s). Though I know zip-point-zero
about the PIC I thought that PWM would allow the LED lights to fade on/off
and other timer features might be added to the program routine?
Thank you all for your responses!!
Sparkey
