Another Controller ...
 
Notifications
Clear all

Another Controller Design

370 Posts
27 Users
0 Reactions
128.2 K Views
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago

I am adding the 32 channel files to this thread for anyone who would like to take a whack at the code, It is only setup for one device at the moment, PIC18F45K22, more development is needed for the status indicator which I explained in my earlier posts, I will have the schematics done by next week sometime then add them to this thread. I am still waiting for my 64 channel device so I can try my code for that when it comes in. Then I will post the 64 channel code so if anyone wants they can try that. The device is a PIC18F87K90 TQFP, by the way all this code originated from P.Short, it has been modified to accommodate all the various devices that we have been using for the Simple Renards
Thanks again Phil.


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago
LabRat wrote:I'm interested... and will also try and find time to see what the effort would be to tweak to a single sided (home-etch) version. Like we had done with the SIMPLE 16 (I have 3 of those running in one enclosure.. in hind-sight, I should have used "top mount" jacks. 🙂 )

I know this post is 6 months old but I am curious if you ever went forward with a single sided Simple 24. I have successfully etched and built several simple 16 and would like to try the 24 channel version if it is available. If not I might try to move the traces around myself. Just thought If its already done I would use yours.

Tyler


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago
tstraub wrote:I know this post is 6 months old but I am curious if you ever went forward with a single sided Simple 24. I have successfully etched and built several simple 16 and would like to try the 24 channel version if it is available. If not I might try to move the traces around myself. Just thought If its already done I would use yours.

Tyler

Nope. "Life" got in the way.


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago

OK, I'll give it a go then. "Life" here is pretty slow and I'll be in the seated position for at least 3 weeks due to a dislocated knee-cap.

Tyler


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago
tstraub wrote:OK, I'll give it a go then. "Life" here is pretty slow and I'll be in the seated position for at least 3 weeks due to a dislocated knee-cap.

Tyler

Also consider that the cost of small boards at places like Seeedstudio, makes the value in a home etch questionable. It's your time, you will have to evaluate it's value.
For me, I use "home etch" when I'm developing an initial concept, but have opted to have actual boards made for "finished" product. The solder mask alone makes it
so much easier to deal with.

Good luck though. I don't mean to sound like a wet blanket. It's a fun learning curve.


Reply
steve_hirst
Posts: 296
(@steve-hirst)
Reputable Member
Joined: 17 years ago
Mactayl wrote:I am adding the 32 channel files to this thread for anyone who would like to take a whack at the code, It is only setup for one device at the moment, PIC18F45K22, more development is needed for the status indicator which I explained in my earlier posts, I will have the schematics done by next week sometime then add them to this thread. I am still waiting for my 64 channel device so I can try my code for that when it comes in. Then I will post the 64 channel code so if anyone wants they can try that. The device is a PIC18F87K90 TQFP, by the way all this code originated from P.Short, it has been modified to accommodate all the various devices that we have been using for the Simple Renards
Thanks again Phil.

Mac did you ever get the schematics done for the 32 channel version? also how did the 64 channels turn out? I ran 4 of the simple16's and 4 of the simple24's in my show this year and they worked great. I only had 1 failure on a home etched 16 and that was because of water intrusion. Not the boards fault, it was mine.


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
steve_hirst wrote:Mac did you ever get the schematics done for the 32 channel version? also how did the 64 channels turn out? I ran 4 of the simple16's and 4 of the simple24's in my show this year and they worked great. I only had 1 failure on a home etched 16 and that was because of water intrusion. Not the boards fault, it was mine.

Steve,

I will make up some schematics hopefully this week for the 32 channel version, as for the 64 channel version at this point there is not enough access ram on the device for all the variables, I am going to try for a 48 channel version instead of the 64 channels. I have been busy on the 20 channel random Starr Burrst modules at the moment so the 48 channel stuff is on the back burner sort of speak. As soon as I get the schematics done for the 32 channel stuff I will post them.


Reply
steve_hirst
Posts: 296
(@steve-hirst)
Reputable Member
Joined: 17 years ago

no big hurry, If your tied up doing something else I can wait. I am in the middle of working on some other things also.


Reply
Posts: 393
(@soakes94)
Honorable Member
Joined: 18 years ago
Mactayl wrote:I am adding the 32 channel files to this thread for anyone who would like to take a whack at the code, It is only setup for one device at the moment, PIC18F45K22, more development is needed for the status indicator which I explained in my earlier posts, I will have the schematics done by next week sometime then add them to this thread. I am still waiting for my 64 channel device so I can try my code for that when it comes in. Then I will post the 64 channel code so if anyone wants they can try that. The device is a PIC18F87K90 TQFP, by the way all this code originated from P.Short, it has been modified to accommodate all the various devices that we have been using for the Simple Renards
Thanks again Phil.

Just wondering if this is the most recent version of the code? I was thinking about building a few of these and thought I would check I have the right code before I start programming pics 🙂

Steve


Reply
tstraub
Posts: 525
(@tstraub)
Honorable Member
Joined: 18 years ago
soakes94 wrote:Just wondering if this is the most recent version of the code? I was thinking about building a few of these and thought I would check I have the right code before I start programming pics 🙂

Steve

That code is out of date it only works on one of Macs SR32's built on proto board. The channel map is wrong for the board in the File Library because I changed a few I/O pins to keep the board single sided. Use the firmware in the first post of this thread. The channel map is correct and it supports start address.

Tyler


Reply
Page 37 / 37
Share: