Another Controller ...
 
Notifications
Clear all

Another Controller Design

370 Posts
27 Users
0 Reactions
128.2 K Views
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
P. Short wrote:Is there some OC-output part that you could use instead of the 244? That would be useful for people who want to drive some of the LED floods, etc, which use 12V or 24V.

Something like the ULN2803L Darlington LED Drivers?


Reply
Posts: 789
(@chilloutdocdoc)
Prominent Member
Joined: 18 years ago
Mactayl wrote:Just another bit of info the 80 pin TQFP is half the price of 2 PIC18F4620's
and the 74HCT244 are less then 25 cents each

Oh. *stupid grin* ignore comments from the uninformed as always.

Back to your regularly scheduled program.


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
P. Short wrote:Is there some OC-output part that you could use instead of the 244? That would be useful for people who want to drive some of the LED floods, etc, which use 12V or 24V.

My mistake on the ULN2803L, yes there are some open collector devices I could use for the 64 channel setup, I will order some today.


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
Mactayl wrote:My mistake on the ULN2803L, yes there are some open collector devices I could use for the 64 channel setup, I will order some today.

Something more like the SN64BCT757 Octal Buffer/Driver 128 ma open colletor


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

Well,

After being slack for way to long, i got around to doing some testing today.

Mac sent me the 24 Channel Firmware and i must say it looks like its working 100% on the board i got made.

It needs to use a crystal to get the needed speed as the internal 16Mhz doesnt seem to allways be quick enough.

I am running a 20Mhz crystal and it seems to be fine, I have some other speeds but our maths says anything inthe 20-25Mhz range should be fine.

Once i have tested a couple more pics and cleaned up the older 16 channel pics from the code either myself or mac will post the finished results.

If you have one of my boards and want to test i can sen the you current files if you like.

Peter


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago

As Peter mentioned we need to use the ext. osc. 20-25 MHz due to fact when I ran the devices at 32 Mhz they looked fine on the bench when using small LED’s. So last week I built up some SSR’s and ran incandescent lights and there were only about half the dimming levels available, I let Peter know what was going on and we decided to go back to the original Timer codes. I am using 25mhz Xtals for the osc and all dimming levels are working with 16 and 24 channels at 38400, 57600 and 115200 baud rates so far with the PIC18F2420, 2525, 2620, 4520, 4525 and 4620,


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
Mactayl wrote:As Peter mentioned we need to use the ext. osc. 20-25 MHz due to fact when I ran the devices at 32 Mhz they looked fine on the bench when using small LED’s. So last week I built up some SSR’s and ran incandescent lights and there were only about half the dimming levels available, I let Peter know what was going on and we decided to go back to the original Timer codes. I am using 25mhz Xtals for the osc and all dimming levels are working with 16 and 24 channels at 38400, 57600 and 115200 baud rates so far with the PIC18F2420, 2525, 2620, 4520, 4525 and 4620,

Well after some time of more testing and code changes it looks like there may be light at the end of the tunnel, I need Peter and Phil to look over the latest changes for running the device at 40 Mhz, the dimming levels are solid for 1 thru 255, I also made a Proto board for the Renard Simple 16 with Triacs installed, if this PCB works out we will design a PCB for the 16,24 and 32 channels versions with triacs so it will be available as a full controller with triacs.

Simple16 Triacs

Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago

Mac:

This is somewhat off topic, but I noticed that your prototype is built on perf board (RS perf board if my eyes don't deceive me) -- how did you get the .05" pitch pins on the RJ45 connectors to go through the .1" pitch holes in the perf board?

I've only built one thing on a standard perf board that needed the connector and I bent the hell out of the pins to make it work -- I'm hoping there's a trick ...

\dmc


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago
dmcole wrote:Mac:

This is somewhat off topic, but I noticed that your prototype is built on perf board (RS perf board if my eyes don't deceive me) -- how did you get the .05" pitch pins on the RJ45 connectors to go through the .1" pitch holes in the perf board?

I've only built one thing on a standard perf board that needed the connector and I bent the hell out of the pins to make it work -- I'm hoping there's a trick ...

\dmc

I bent one row of pins to the right slightly and the other row to the left slightly so they would line up with each other and they fit right in the PCB


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
Mactayl wrote:I bent one row of pins to the right slightly and the other row to the left slightly so they would line up with each other and they fit right in the PCB

I guess I was more smart than I gnu ... 😉 ...

\dmc


Reply
Page 36 / 37
Share: