martijnkooi
@martijnkooi
Trusted Member
Joined: Oct 4, 2015
Topics: 4 / Replies: 43
Reply
RE: ESPixelStick - E1.31 WiFi Pixel Controller

Add controller using the ipaddres and the universe corresponding to the espixelstick. Then patch the pixels and it should work. Plenty of videos on Yo...

9 years ago
Reply
RE: How to sync video (projector) on PI (falcon slave)

jwamsley07 wrote:I've been through the same problems. Last year I fought with the video being 1.9 seconds behind on the remote pi. I ended up modify...

9 years ago
Reply
RE: How to sync video (projector) on PI (falcon slave)

Exactly what I ment. I run my sequence and audio on the FPP master and it triggers a DMX channel 1 (10) and channel 2 (150). This will start my video ...

9 years ago
Topic
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

Hahaha, no problem dude 🙂 I tried the 4* multiplier. This gives me a proper 3.3v output. This is however too low for the irf540 mosfet. The led lig...

9 years ago
Forum
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

Barnabybear wrote:Hi, sorry - my bad. Arduinos only have a 8 bit analog output (0 to 255) the ESPs / Wemos are 10bit (0 to 1023). An easy fix *4. ana...

9 years ago
Forum
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

martijnkooi wrote:Hi. Sorry for the confussion. When I measure voltage I did measure it directly on the gpio pin out. So wemos is limiting output of...

9 years ago
Forum
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

Barnabybear wrote:Hi, that’s good news. The first thing that comes to mind is that the IFR540N may be the issue. These FETs are great with 5V systems ...

9 years ago
Forum
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

Hi, I tried to setup the Wemos, I do get proper output in the serial monitor: we have data 175 107 207 175 107 207 I wired everything as describe...

9 years ago
Forum
Reply
RE: Potential E1.31 / WiFi mod for dumb strips & floods.

Hi Barnaby. A little help with this sketch please. I want to use a wemos running 2 rgb strips. Should I start with flashing espixelstick and overwri...

9 years ago
Forum
Reply
RE: ESPixelStick - E1.31 WiFi Pixel Controller

Thanks Barnaby! Will give it a try.. Barnabybear wrote:Hi, have a quick look at the link below, it should point you in the right direction. As the W...

9 years ago
Reply
RE: ESPixelStick - E1.31 WiFi Pixel Controller

hi there, I got my wemos-espixelstick running trough fpp player but I also have some dumb rob nodes which I like to add to my (halloween) setup. Is ...

9 years ago
Reply
RE: Falconplayer espixelstick wiring question

kev wrote:- The schematic for the device you said you were using in post#4 shows that is has an on-board 3.3v regulator, so no other would be required...

9 years ago
Reply
RE: Falconplayer espixelstick wiring question

kev wrote:I don't have a good drawing package, but here is my suggestion. The Wemos will only use as much power as it needs as DemoV3 said. But I do...

9 years ago
Reply
RE: Falconplayer espixelstick wiring question

DemoV3 wrote:Not sure what board you are using but a circuit will only draw what it needs. Can have 100 amp power supply and a single LED, will only u...

9 years ago
Page 1 / 4