Falconplayer espixe...
 
Notifications
Clear all

Falconplayer espixelstick wiring question

9 Posts
5 Users
0 Reactions
3,315 Views
Posts: 47
Topic starter
(@martijnkooi)
Trusted Member
Joined: 11 years ago
[#46058]

Hi there,

As Halloween is within 1 month I like to start with the wiring diagram. I do have some questions how to wire all the nodes.
This is my setup I have so far:

2* 5v 30A power adapters
10 * wemos controller
1000 pixel nodes
1 * raspberry pi

I'm not confident wiring the wemos directly to the adapter because 30 amps is way to much power.
How do I make sure the controllers are not toasted when I power them?

thanks! Martijn


8 Replies
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Hi, one way is to use an automotive (car) blade fuse and crimp some shielded (covered in plastic) female spade terminals on the feed wires. There are lots of other off the shelf and custom made fuse / power distribution boards about.


Reply
Posts: 60
(@demov3)
Trusted Member
Joined: 10 years ago

Not sure what board you are using but a circuit will only draw what it needs. Can have 100 amp power supply and a single LED, will only use what it needs. To protect the board from anything going wrong find out exactly how many amps the board will need or can pass through and fuse to that level. I use mini ATC fuses for my stuff.


Reply
Posts: 47
Topic starter
(@martijnkooi)
Trusted Member
Joined: 11 years ago
DemoV3 wrote:Not sure what board you are using but a circuit will only draw what it needs. Can have 100 amp power supply and a single LED, will only use what it needs. To protect the board from anything going wrong find out exactly how many amps the board will need or can pass through and fuse to that level. I use mini ATC fuses for my stuff.

Hi, I'm using these boards, https://wiki.wemos.cc/products:d1:d1_mini
I want to directly connect via amp these boards, so it is easier to wire all the boards.
See diagram:

please advice 🙂


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago

I don't have a good drawing package, but here is my suggestion. The Wemos will only use as much power as it needs as DemoV3 said. But I don't know if the Wemos board can pass enough current to the strings without burning the traces on the board. The pixel strings use about 3 amps per 50 pixels, So a 200 pixel string will need about 12 amps if all white lights are chosen. Although I only show one fuse, you should put a fuse on the +5V power going to each string. And you will likely still have to inject power along the string somewhere.

Base setup

Reply
Posts: 47
Topic starter
(@martijnkooi)
Trusted Member
Joined: 11 years ago
kev wrote:I don't have a good drawing package, but here is my suggestion. The Wemos will only use as much power as it needs as DemoV3 said. But I don't know if the Wemos board can pass enough current to the strings without burning the traces on the board. The pixel strings use about 3 amps per 50 pixels, So a 200 pixel string will need about 12 amps if all white lights are chosen. Although I only show one fuse, you should put a fuse on the +5V power going to each string. And you will likely still have to inject power along the string somewhere.

Thanks Kev,

So no need to regulate the power to the wemos.
I bought the pixels at AlieExpress.
They should consume 60ma, 1.8A for 100 nodes
I bought two 30A powersuplies, should be enough for 3300 pixelnodes..

Martijn


Reply
Posts: 1387
 kev
(@kev)
Noble Member
Joined: 12 years ago
martijnkooi wrote:Thanks Kev,

So no need to regulate the power to the wemos.
I bought the pixels at AlieExpress.
They should consume 60ma, 1.8A for 100 nodes
I bought two 30A powersuplies, should be enough for 3300 pixelnodes..

Martijn

- The schematic for the device you said you were using in post#4 shows that is has an on-board 3.3v regulator, so no other would be required.
-100 nodes X 60ma = 6amps.
- two 30A power supplies theoretically would power 1000 pixels at full white (1000 X 60ma = 60A) but would be safer to design for 800.
- if you are using pixel strips, some only have 30 WS2811 chips per 15 meters, but each WS2811 controls 3 LEDs. So your LED count would be 150 per 15 meters.


Reply
Posts: 47
Topic starter
(@martijnkooi)
Trusted Member
Joined: 11 years ago
kev wrote:- The schematic for the device you said you were using in post#4 shows that is has an on-board 3.3v regulator, so no other would be required.
-100 nodes X 60ma = 6amps.
- two 30A power supplies theoretically would power 1000 pixels at full white (1000 X 60ma = 60A) but would be safer to design for 800.
- if you are using pixel strips, some only have 30 WS2811 chips per 15 meters, but each WS2811 controls 3 LEDs. So your LED count would be 150 per 15 meters.

-100 nodes X 60ma = 6amps.:zipped:
Thanks


Reply
Posts: 93
(@kockie)
Trusted Member
Joined: 11 years ago

I did it like this picture:

nodemcu aansluiten

This way it is easier to switch nodemcu in case they get broken. (I had to work in a very wet environment...)


Reply
Share: