What material do yo...
 
Notifications
Clear all

What material do you use for your wireframes?

40 Posts
21 Users
0 Reactions
20.3 K Views
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago

looks great!

don


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

I made a frame from cpvc to strengthen the coroplast while it is hanging on the house fireplace brick. I will have two of these at an angle to one another. they will alternately blink to the beat.


Reply
Posts: 7
(@nickdico)
Active Member
Joined: 12 years ago

Hey team!

I was thinking of starting to make small wireframes, maybe 13"x13" (nothing larger than a foot or foot and a half). I don't own a welder, nor could without having a stable place to use it (no garage just an older wooden shed).

I tried using some old tomato stakes, but it is a pain cutting them up by hand. However they hold form pretty darn well.

Any recommendations on other materials to do small scale wireframes for the outdoors? Thanks!


Reply
T.D.Sutton
Posts: 445
(@t-d-sutton)
Honorable Member
Joined: 17 years ago

I have made a number of "small" wireframes out of so called Galvanised or zinc coated "Number 8 wire" and soft soldered them together at the joints using an overlap for strength. I get mine from a local "big box" store in the garden department in coils of about 20 yards. Four, four-channel stars for the top of my "shooting poles" were made this way for last year and handle the weather and winds fine, they are about 18" - 20" across. See pic below prior to installation.

Wireframe Star

I figure out each length, plus a bit, then straighten it by bending about 1 inch at one end at 90 deg, fix that end in a vice and then put a battery electric drill on the other end in very low gear and twist the wire along it's length. This has the effect of straightening the wire and partially "work hardening" it which helps to keep it straight. If a joint looks like it is going to be a bit weak I bind the joint with thin copper wire and then solder over that to keep it all in place.

Soldering Galvanised or Zinc coated wire you will need to have available a hydrochloric acid based flux, this combines with the zinc and accepts the solder beautifully. I am often lazy and use the liquid flux and still use my supply of rosen cored solder to do the soldering, it is no problem at all. Beware though you must thoroughly wash the job down with water to remove any traces of the acid flux after completing the job.

The flux I use here in New Zealand is named "Duzzall" this comes in a green container, and is a mixture of Hydrochloric acid and Phosphoric acid, which allows easy soldering of stainless steel as well as Zinc plated steel.

Terry


Reply
Posts: 7
(@nickdico)
Active Member
Joined: 12 years ago

That's great and very helpful. Thanks Sutton!


Reply
Posts: 209
(@rick-todd)
Estimable Member
Joined: 14 years ago

Hi Terry,

Those stars look great! When you say solder them together above are you using a gas torch (propane or Mapp) or something else? I'd like to try something like that and I already have a Mapp gas torch and I'm hoping to use it.

Thanks

Rick


Reply
T.D.Sutton
Posts: 445
(@t-d-sutton)
Honorable Member
Joined: 17 years ago
Rick Todd wrote:Hi Terry,

Those stars look great! When you say solder them together above are you using a gas torch (propane or Mapp) or something else? I'd like to try something like that and I already have a Mapp gas torch and I'm hoping to use it.

Thanks

Rick

Thanks for your comments, Rick,

I use a mains powered soldering iron, one with a "reasonable" sized copper tip. The one that I soldered the star frames with was a 65 watt "english made" "Henley Solon" iron. I have had it for more years that I care to remember - likely 60yrs!! In fact it was the first Iron that I owned and given to me by my father as a present. It is effectively a lower powered version of a plumbers, tin-smiths, or sheet metal workers iron. You need to have a reasonable amount of heat reserve available in the head to keep the heat transfer going to get reliable & strong joints. I have just finished modifying 16 small "Mini-trees" made exactly the same way as the stars, and on this occasion I used a slightly higher powered Iron that I acquired recently and this actually worked better, I think it is about a 125 watt version and as with the 65 watt they have no temperature control, and appear to stabilise themselves at a suitable temperature for good solder joints.

I have attempted using a gas torch, but have not had much success as the flame is too concentrated and hot which easily "burns" the solder, making it crystalize, while taking away any flux in the process. This is really counter-productive as the flux is essential to to a good joint, and does not allow the opportunity to build up the solder as the joints is created, to smooth out the joint and correct and irregularities - ie. make it "Look Good" 🙂

I trust that this is an answer to your question, best of luck with your project.

Terry


Reply
Posts: 928
(@arw01)
Noble Member
Joined: 13 years ago

Photos please gents of the good the bad and the ugly, especially joints that hold up. On the list yet this year, are large balls to hang from a "mega tree" bull pine I have. This has been a bucket list item for the wife since she was a child.

Sent from my Sony Tablet S using Tapatalk


Reply
Posts: 209
(@rick-todd)
Estimable Member
Joined: 14 years ago

Thanks Terry,
That's exactly the answer I was looking for. I tried the gas last night and had no success. I'll try a bigger iron and see how that works.

Thanks for your help

Rick


Reply
T.D.Sutton
Posts: 445
(@t-d-sutton)
Honorable Member
Joined: 17 years ago
Rick Todd wrote:Thanks Terry,
That's exactly the answer I was looking for. I tried the gas last night and had no success. I'll try a bigger iron and see how that works.

Thanks for your help

Rick

Having a "sizable" heat reservoir/reserve in the soldering iron tip makes this sort of soldering a lot easier as the wire draws the heat away quite rapidly and attempts to cool the tip. If the tip is too small, without sufficient heat reserve, the result can be that the soldered joint can cool below the melting point of the solder, producing a rather "dodgy" joint.

This is exactly what can happen if a "low powered" soldering iron is used to solder up a PC Board. My experience over the years has been that using a "hot" iron to make a soldered joint, with minimal time in contact with "whatever is being soldered", is far better than using a low powered iron and having to stay in contact with the joint component for a long time. If that happens the iron's heat transfers all over the board and components while it is trying it's best to bring the joint up to soldering temperature, possibly destroying/damaging the components and/or the board in the process.

My $0.02 worth anyway 🙂

Terry


Reply
Page 4 / 4
Share: