What material do yo...
 
Notifications
Clear all

What material do you use for your wireframes?

40 Posts
21 Users
0 Reactions
20.3 K Views
Posts: 564
(@jackfrost)
Honorable Member
Joined: 16 years ago

Well , something else I don't recall anybody mentioning . If you are going to build taller wireframes ( like I did with 2 snowmen and 2 Christmas trees ) , then the 3/8 rebar will have a LOT of give to it ( more than I was happy with )
And you could also get a stick welder for 110 AC ( usually 90 amps which is plenty strong enough for 3/8 rebar and 1/4 also )


Reply
Posts: 146
 Dan@
(@dan-2)
Estimable Member
Joined: 14 years ago

Taller wireframes i would suggest putting a 1/4 or 3/8 as a backbone (depending on size of wireframe). Run them from to bottom, depending on the width, may take a couple to help stabilize and you may need to use guide wires front and back.

Stick welder would work, but would not be as easy for a beginner to pick up on as a MIG would be. MIG is the easiest for a new welder to get the hang of.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I've seen many people here and other forums start with flex core wire then move up to mig. The comments are always "why didn't I do this sooner". It's quicker, easier, easier to tell if the weld is good. So I would move up to one that can do MIG.

Brian


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago
Dan@ wrote:Taller wireframes i would suggest putting a 1/4 or 3/8 as a backbone (depending on size of wireframe). Run them from to bottom, depending on the width, may take a couple to help stabilize and you may need to use guide wires front and back.

Stick welder would work, but would not be as easy for a beginner to pick up on as a MIG would be. MIG is the easiest for a new welder to get the hang of.

When I build my frames, I always reinforce the sides with 3/8" or 1/2" round cold rolled steel. Keeps them rigid, and you can not really bend it much without heating it with a torch. The larger dia. steel also forms the 'legs' which goes about 8-10" in the ground for support. I tack the 1/4" frame to the front of the larger bracing, leaving a 1/16" gap to allow the light clips to be attached, which is not necessary if you use rope light (I use LED mini's on my frames). Also, I HIGHLY RECOMMEND having all wire frames Powder Coated. I don't care how carefully you paint them, you will get rust developing at welds and scratches at some point. It's a real PITA to have to unstring a frame to touch up the rusty spots. Once Powder Coated, they are ususall trouble free for years.

As for flux core vs GAS, believe us, there is NO COMPARISON in the quality and strength of the welds for a newbie welder (like me).:(


Reply
Posts: 34
(@jachip)
Eminent Member
Joined: 14 years ago

I have made lots of wire frame 3/16 and 1/4 hot steal is the eas to go for bending any welder will do unless it is going to hold lots of wgt you can buy it at home depot in with the thread rods most hardware stores carry it you can also call around to some steal suppliers it is cheaper from th
em.


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

I made a Bell and a Angel Bell from # 9 wire from the pattern of eShepardsOflights.com. Now I need some way of attaching the LED strings to the wire. It seems I can't use the same 1/4" hardware cloth with #9 wire because it is too tight of a fit. eShepards used ceiling hanger wire which is smaller in diameter which would work with 1/4" hardware cloth.

I deviated from that pattern And not realizing the mistake I made till I started trying to use hardware cloth, I now need a different way to attach LED strings to the #9 wire and make it look good.
Any suggestions?


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
11Bravo wrote:I started trying to use hardware cloth, I now need a different way to attach LED strings to the #9 wire and make it look good.
Any suggestions?

If the LEDs almost fit, you could put a screwdriver or something into the target cells and gently enlarge them.

For other props where hardware cloth did not fit well, I used duct tape successfully. An example photo is on page 8:
http://downloads.eshepherdsoflight.com/Howidid-NativityFigures.pdf

I used gray duct tape, which was slightly visible. Black would not be so obvious.

Yet another option would be to zip-tie, glue, or tape those little light holders onto the wireframe.

don


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

Thanks Don, I did try to enlarge the square but there still was not enough space between the bulb socket and the #9 wire so that the socket could lie down and I couldn't get the insulated wires in the other side very well. And with those sharp pointed wires possibly poking holes in the insulation, making a it a hazard. So I gave up on trying to use the 1/4" wire cloth. I think if I could find some 5/16" I could make better progress. But that isn't a popular size and more difficult to get locally.. Another thought I have going is to try some coroplast. Place the frame on the coroplast and make holes in it along the frame and insert the bulbs and tye rap it to the wire. I'm going to try and pick up a piece or coroplast tomorrow and give it a try.


Reply
Posts: 2168
(@djulien)
Noble Member
Joined: 19 years ago
11Bravo wrote:Place the frame on the coroplast and make holes in it along the frame and insert the bulbs and tye rap it to the wire. I'm going to try and pick up a piece or coroplast tomorrow and give it a try.

That sounds like a good option. Let us know how it turns out!

don


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

This is what I came up with so far. I can take the frame off the coroplast and make another outline on another piece of coroplast. I don't really need the frame after I punch the bulbs thru the plastic. But I'll probably make some sort of frame on the border to stabilize it. I plan to hang two of them on the front of the chimney at an angle to each other. and they won't be subject to any wind load.

Dropbox Logo Dropbox File (Private or Invalid)


Reply
Page 3 / 4
Share: