powering pixel str...
 
Notifications
Clear all

powering pixel strings

8 Posts
5 Users
0 Reactions
3,244 Views
Posts: 8517
Topic starter
(@angus40)
Illustrious Member
Joined: 15 years ago
[#20863]

If i plan to power pixel strings from both ends using the same power supply

example . using a 5v 60a supply with an e681 and 16 strings of 42 ct.

would it be absolutely neccessary to run +v and grd to the far end or would +v be enough being the 681 is - switching.

I would also like to know if any one eles has experienced this :

connect a 50 count string to the e68* and set the pixel count to less than 50 in the config .

while running sequences on this, any pixels that are not in the config randomly tend stick on .

I have had this happen numerous times while testing .

My question in regards to this is , are pixels dropping voltage when they are in the off state or is 00000000 still using power .

I believe Cptn kirk measured a draw while in the off state that he mentioned in another thread.

Richard

Ps I guess i am going to have to stop being lazy and start using a vm.


7 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

There will always be some draw from the pixel chips even with the LEDs off since they are active components - not exactly sure what that amount is but guessing a few mA per pixel. Easy enough to toss a meter in-line when off to find out.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

Lots of things to answer:
I’ve had just one string of 42 pixels attached to a E681 and powered it from a 20 Amp supply – when folded back so the 1st and 42nd where side by side, with all pixels on full white they were not the same colour.
So the problem is the current draw when all 3 (red – green - blue) are drawing full power the cable that is connecting the pixels is inadequate. But we drive the price down and savings have to be made somewhere.
There are many fixes:
Don’t run your pixels at full power – an interesting one – we think a full red (dmx 255) is bright – but the we’ll add a 255 green and a 255 blue to that - and create a very bright white (in theory 3 times brighter) what would be good is if we had a sequencer that faded back the red as it added the other colours so that we maintained an intensity. But at present none of the sequencers can do that – next year – I think so.
So we have to mess with what we’ve got:
Powering what we’ve got – as we do now – we power the start of the pixels (partly because it’s nearest and partly because we have to go there because we need to get the data to the first pixel) – just from a power point of view it would be better to power the pixels from the middle (on a string of 50 – you only have 25 each way on less than ideal cable). The power cable is running further so it needs to be larger – but it can be.
Feeding power from both ends – this is a minefield – firstly to feed a +ve and –ve to the far end of the pixels – the easiest thing to do is take two wires from your power supply and up to the top of your tree and feed all your pixels – cool it will probably cure any power problems – but you then have bypassed the fuses on you controller (E68x) not good if things go wrong. So take 32 cables from the fused outputs up to the top of the tree – not going to happen.
Volt drop occurs in both the +ve and –ve lines – so by improving one of them you will make things better. Improving the +ve is hard work as you need to fit lots of new fuses or run lots of new cables. The –ve on the other hand is not fused and is common to all the strings – so my advice is to get the fattest bit of cable you can find (old car jump leads would be not be out of the question) and common the –ve’s at the top of the tree – then use these to connect back to the power supply. It’s the simplest way to reduce volt drop.
As to the pixels drawing current whilst at R=0 G=0 B=0 – the control IC will draw power but the led will draw 0 which is 60mA less than at R=255 G=255 B=255.
Just my thoughts – feel free to comment.


Reply
Posts: 75
(@phillikl)
Trusted Member
Joined: 18 years ago

Unfortunately everything wastes power (wire, IC's, LEDs) and converts it to heat; nature of electricity. If you had an extremely sensitive lumin detector you would find out that no 2 pixels on a string would have the same intensity or color. While our eyes are not sensitive enough to notice (until we hit that 42sh pixel) the voltage reduction will come to a point to where the led cannot light. Correct me if I'm wrong, but you cannot simply connect the far end to source without first breaking the positive leg somewhere in the middle.

As for the pixels sticking on, this is erratic operation because they don't have any portion of the instruction left to actually tell them what to do. They may be picking up radicle instructions from the resonate RF on the lines. As BB hashed out, the ws2801 chips are extremely sensitive to noise, this could be causing the lock effect on those uninstructioned pixels.


Reply
Posts: 8517
Topic starter
(@angus40)
Illustrious Member
Joined: 15 years ago

thanks for the replies . I guess i will resort to clipping the 255 level via dimming curve settings in hls and see how that works. Brian an BB you are both using the same pixels as I , i am sure your wrestling with this also.

I have yet to power the strings since i cut the xtra 8 pixels off from each , maybe the pinkish won't be as noticable on the last 25%.

if it is I will run 10awg wire to the top and power from that end also.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago
phillikl wrote:Correct me if I'm wrong, but you cannot simply connect the far end to source without first breaking the positive leg somewhere in the middle.

There's no reason that I can see why you should have to do this. The +V wire is parallel to all pixels, so connecting to it in multiple locations and supplying power is just propping up the supply voltage level, and should work without a problem.


Reply
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago

If your running pixels along a roof line or something like that and need to inject power – this type of thing might be good (the volt drop reduces as the supply voltage increases). Run 12V (or even 24V) out to the point that you need to inject power then use the DC to DC converter to step down to 5V.
On a side note, how do you make that and ship it to the UK for that price?


Reply
Posts: 75
(@phillikl)
Trusted Member
Joined: 18 years ago

Oh! Thanks mark, forgot to add the second power source bit. I hate how iPhone truncates the screen when typing.


Reply
Share: