Notifications
Clear all

cat5 current

15 Posts
8 Users
0 Reactions
10.4 K Views
Posts: 577
(@photovor)
Honorable Member
Joined: 19 years ago

dirknerkle- I don't want to derail this topic much further, but I'm aware that you weren't taking my comments out of context, and I understood what you were saying, that's why I just added additional clarification, nothing personal, not a personal snipe.

And you're also right, it only takes a small amount of current...

"A common misconception is that larger voltages are more dangerous than smaller ones. However, this is not quite true. The danger to living things comes not from the potential difference, but rather the current flowing between two points. The reason that people may believe this can be explained by the equation V = IR. Since V is directly proportional to I, an increase in voltage can mean an increase in current, if resistance (R) is kept constant.

The amount of damage done by the electric shock depends not only on the magnitude of the current, but it also on which portions of the body that the electric current is flowing through. The reason for this is that different parts of the body have difference resistances, which can lead to an increase in current, evidenced by the formula V = IR.

An interesting fact to note is that it takes less alternating current (AC) to do the same damage as direct current (DC). AC will cause muscles to contract, and if the current were high enough, one would not be able to let go of whatever is causing the current coursing through the body. The cut-off value for this is known as the "let-go current". For women, it is typically 5 to 7 milliamperes, and for men, typically 7 to 9 milliamperes. This is dependent on the muscle mass of the individual."
-Quoted from The Physics Factbook

Now we're all that much smarter. :p


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Back to the original question...although it's sort of hard to figure out what the question was when there isn't any punctuation.

Anyway, the resistance of 24 AWG copper wire is around 2.5Ω per 100 feet. If you assume a current draw of 0.5A and 10 feet of wire, the voltage drop is 0.25Ω * 0.5A * 2, or 0.25V, which is probably not noticeable. If you have 100 feet of cable, the drop is 2.5V, which definitely would be a problem. YMMV.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Just to make it clear, I think that it is a bad idea to send mains power down CAT5 cable. Despite the reported experiences of some other people in this thread, the cable is not designed nor intended for that use, and is insufficiently robust. I think that it is fairly dangerous to use CAT5 (or CAT6) wire for that purpose.


Reply
Posts: 76
Topic starter
(@dynochris1)
Estimable Member
Joined: 18 years ago

i never intended to send 120vac down the line that to me is crazy. i was just sending the output side of the h11aa1 down the cat5. 5vdc i believe just a zc signal. the only current i was sending is to power the grinch ren-c combo. also 5vdc regulated. no high voltage and the highest current is whatever powers the grinch


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

The ZC ought to work fine -- hardly any current there at all. Cat5 can handle up to 12vdc pretty well, but even at 5v, if the wires short and you're carrying even 1A, you can get some smoke... and possibly fire. So be careful anyway. Don't kink the wires, don't use a staple gun to mount them, don't bend them sharply (you can loop them, but sharp bends are a bad idea), and of course, keep them where nobody will walk on them. Cat5 is not designed for rough handling and if you keep it clean and straight, it can work fine for low voltage, low current situations.


Reply
Page 2 / 2
Share: