how much current can a cat5 cable handle will it support a grinch/ren-c combo if it has a filtered regulated power supply at the lead.
dynochris1 wrote:how much current can a cat5 cable handle will it support a grinch/ren-c combo if it has a filtered regulated power supply at the lead.
unwise to try to carry more than 1A on any of the wires, and don't ever go more than 50V.. ( NEVER EVER EVER put mains on cat5 cable, the insulation is just not up to the task )..
Then theres the depends questions.. you'll have some voltage drop acorss the cable which may or may not be a problem for you.
i think u may have misunderstood. the power supply and regulator are at my pc the zero cross is with the h11aa1 at the pc (well behind it) i just was wondering if the filtered supply line can be sent on the cat5 maybe if i double up the conductors the zc signal should be ok its just a vcc reference fed back to the ren-c
If you are using a regulator resistor on all the Allegro or MBI chips on the grinch you will most likely get away with feeding one this way, as long as the cat5 run is not long. If you are not using the regulator resistor on the allegro or MBI chips you will have to double the conductors and keep the cat5 run short. For power transmission cat5 is only rated to a little over 1/2 amp. A grinch without the regulating resistors will draw over 1 amp.
Just wanted to mention this in response to an above post (and I"m not recommending it, but I'm sharing my experience and knowledge).
I've run 120vac over cat5 without any breakdown issues, mind you, keeping the amperage below 1 Amp, and even less if going a distance. I've even sometimes paired conductors to get a little more current if need be. With that in mind:
The minimum dielectric strength for any insulating material commonly used in cable construction is 100 volts/mil. From other catalogs most CAT 5 insulation is .007" to .015" thick . So you're looking at a minimum 600v rating for most Cat5 insulations. I've seen less insulation on higher voltage lines too. Just think of a motor winding, small diameter wire coated in a epoxy (I know, I know, epoxy vs pvc insulation, but same principal).
Like I said, I've done it, but don't recommend it unless you're completely aware of the dangers, and are familiar with all the variables.
Photovor wrote:Just wanted to mention this in response to an above post (and I"m not recommending it, but I'm sharing my experience and knowledge).I've run 120vac over cat5 without any breakdown issues, mind you, keeping the amperage below 1 Amp, and even less if going a distance. I've even sometimes paired conductors to get a little more current if need be. With that in mind:
The minimum dielectric strength for any insulating material commonly used in cable construction is 100 volts/mil. From other catalogs most CAT 5 insulation is .007" to .015" thick . So you're looking at a minimum 600v rating for most Cat5 insulations. I've seen less insulation on higher voltage lines too. Just think of a motor winding, small diameter wire coated in a epoxy (I know, I know, epoxy vs pvc insulation, but same principal).
Like I said, I've done it, but don't recommend it unless you're completely aware of the dangers, and are familiar with all the variables.
OUCH! While anything is possible, doesn't DIYC have an official position on this? I mean, taken out of context, this could be lethal to somebody. It's one thing to publish disclaimers, but litigation is something that has a price whether or not the disclaimers are heeded.
I lit a match in the presence of gas and because the air ratio is low in open air it typically doesn’t explode so it’s probably OK to do it too.:eek::roll:
I'm not sure how you could take what I said out of context. I was very plain and clear with the facts. This board is about a DIY hobby that involves the creation and experimentation of circuits to control lighting loads.
No one signs a waiver when they purchase blank or populated boards that do not have a UL listing.
I was merely attempting to share my experience. mrpackethead stated to never try anything above 50v. Makes no difference if you say "never try above 120v". My statements were made in regards to the capacity of the insulation. I should also mention that in the US, the voltage to ring a telephone is around 90vac at 20hz. That goes over Cat3/Cat5 cable.
..and it's not the voltage that will kill you, it's the current.
People ask questions to gain knowledge from people who have experience. I'm not saying that running 120vac over Cat5 is correct, but in my experience, and staying within the technical specifications of the insulation and wire guage, I've had no issues.
Photovor wrote:People ask questions to gain knowledge from people who have experience. I'm not saying that running 120vac over Cat5 is correct, but in my experience, and staying within the technical specifications of the insulation and wire guage, I've had no issues.
I appreciated your description of the insulating properties of cat5, to help explain conditions under which it might or might not be safe. I think the "why" question really does fit into the DIY theme, in addition to all the disclaimers.
don
Photovor wrote:..and it's not the voltage that will kill you, it's the current.
Not true. A person's heart can easily go into fibrillation due to a shock with very little current -- death can happen then because of the lack of blood flow.
I wasn't taking YOUR comments out of context, Photovor. It's obvious that you're a knowledgeable guy and have been very careful about it. My concern was for others/newbies who might take a quick read and decide it's safe as can be without having a very good grasp of the safety issues at hand.
IMO it's almost always better to err on the safe side and go with the manufacturers' recommendation. 😉
