I would disagree with running the 14/3 and trying to get 30 amps. Only because it would be rejected by any inspector where I live. I have been doing residential electric for over 30 years now.
Check with an electrician for where YOU live and make sure you meet the NEC codes for wiring, circuits, and any local requirements before you install things.
Better safe than sorry when electricity is concerned. It is always easy for someone to say things but they may not be applicable where you live.
beeiilll wrote:I would disagree with running the 14/3 and trying to get 30 amps. Only because it would be rejected by any inspector where I live. I have been doing residential electric for over 30 years now.Check with an electrician for where YOU live and make sure you meet the NEC codes for wiring, circuits, and any local requirements before you install things.
Better safe than sorry when electricity is concerned. It is always easy for someone to say things but they may not be applicable where you live.
I agree with Bill. There's a big difference between what can be done and what should be done. 240 V shocks are deadly. Check with your local building department. You should have a permit for this anyway in most places. We don't want to be reading about your untimely demise.
beeiilll wrote:I would disagree with running the 14/3 and trying to get 30 amps. Only because it would be rejected by any inspector where I live. I have been doing residential electric for over 30 years now.Check with an electrician for where YOU live and make sure you meet the NEC codes for wiring, circuits, and any local requirements before you install things.
Better safe than sorry when electricity is concerned. It is always easy for someone to say things but they may not be applicable where you live.
First let's clarify a little: Not getting 30A, but 2-15A circuits. They are run independently of each other.
Home Depot and Lowes stocks & sell 14/3 Romex. With your 30 years experience tell me where it is used in such a volume that they stock it?
I agree to check local inspectors. Sometimes an inspector will reject NEC installations.
ezellner wrote:I agree with Bill. There's a big difference between what can be done and what should be done. 240 V shocks are deadly. Check with your local building department. You should have a permit for this anyway in most places. We don't want to be reading about your untimely demise.
All this is true, and scary, but 240V exist in most every home. Should we run from those circuits too:
Dryers, Air Conditioners, Ranges, Cook Tops, Ovens, Welders, compressors are all 240V
I'm not sure why you place FEAR out there? Is it that you do not understand the concept. 120V shocks are deadly too - so let's not talk any electrical here.
Members like MartinMueller2003, MikeKrebs, dmpeaceman, Emuney18 and pixelpuppyhave learned from the concept....even if their local inspector will not allow, or they decide not to use themselves, they've learned another wiring technique.
I already made the disclaimer: I am only giving you food for thought. You must verify with your local code, anything/everything I have discussed prior to using."
I just feel there are other ways of doing things, and I like to share.
Here is a little NEC Code reading if you like....NEC is always changing so this may not be the latest.
https://www.jadelearning.com/jadelearning/thejunctionbox/multiwire-branch-circuits-nec-210-4/
Well, I run 14/3 w/ground for ceiling light circuits a lot for hallways with 3-way switches as each end of the hall or stairs. Sometimes have to run 14/4 if there is a need for a 4-way switch somewhere along the line. I run 14/3 w/ground for bedroom lights and also install a ceiling fan rated box so that the customer can have a light and a fan if they want without remodeling anything.
14/3 w/ground is common to run for interconnected smoke detector circuits by code as well so one can burn through a bunch of it easily in a larger multi-bedroom, hallway, and living area rooms that require detectors. Most electricians I know though will run 12/2 for outlets and 12/3 for switched outlets along with 20 amp receptacles. Too many cases of overloading 15 amp receptacles as more and more tech stuff gets plugged in. Most of the electricians that I work around and with do 12 gauge wire with ground, 20 amp breaker, and 20 amp receptacles on our jobs nowadays. Cost increase is minimal and much safer and peace of mind for families
Your drawing in post 37 appears to show a single common neutral return line for 2 hot lines which is a no-no almost everywhere that I am aware of. It certainly would never pass an Under Writers inspection and probably not an NEC inspection if you have a good inspector who does the job and not just shows up to collect a fee (It does happen but they can get their license taken away easily if anyone turns them in!
I buy my 12/2, 12/3, 14/2, and 14/3 wire (all with ground) on 1000 foot reels for my jobs. I also use insulated staples and comb out my wire runs so that they are flat and straight. My inspectors for either NEC or Under Writers are very happy with my work and I rarely have any discrepancies to fix unless it is some new reg that I had not gotten yet and they still give me the benefit of the doubt 99.9% of the time without question and a free re-inspection if I want one even though they will sign off that the work is done before I have it done when they leave. I consider that the trust that I have worked for with them as well as I make them go over at least every 3rd house with me piece by piece to make sure that I am "on code" and doing what they want to see.
Codes can change very quickly and often so it pays to stay informed and abreast of things. Something that may be legal today may not be tomorrow. Unless you do electrical work daily, it can change and you won't know it.
I always tell people to get a licensed electrician if you are not sure about anything to do with electricity! It only takes one mistake to kill you so don't risk making that one! The best rule of thumb for wiring is to use wire rated for what you are trying to do first and then make sure that the breakers, switches, and outlets all meet that rating as well. I always think of any circuit as 3 wires (hot, neutral, and ground) that are all the same size and capability with any switches and outlets being rated the same as the breaker.
Of course, there can be exceptions to this but so far this has worked well for me for 30 years! There are also shortcuts and dubious ways to run things and save a few dollars but the cost of a new house keeps me from shortcuts pretty much.
I want to live peacefully and content in knowing that my electric is the least of my worries!
