Which pixel strips?
 
Notifications
Clear all

Which pixel strips?

18 Posts
13 Users
0 Reactions
6,003 Views
Posts: 184
(@micromutt)
Estimable Member
Joined: 12 years ago

Anyone in the US selling 12bit pixels in all forms?


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

I really don't know enough about pixels. But have done some searching on difference between WS2812b pixels and WS2811 pixels. It's all confusing to me. I haven't come across the difference yet. All I have determined is the WS2812b is better than WS2812 and nothing about the WS2811 versus the Ws2812b

I'm planning on doing some 2" HDPE arches also this season. I appreciate some post that say 30pixels/m is a good look and that helps on decision makeing. But about WS2812b and WS2811, I'm still in the woods on.


Reply
Posts: 928
(@arw01)
Noble Member
Joined: 13 years ago

Besides stellascapes no.

have to order 5v pixels out of China so far, been looking for 12v TLS3001 pixels myself.


Reply
navyav8tr
Posts: 229
Topic starter
(@navyav8tr)
Reputable Member
Joined: 13 years ago
dmcole wrote:+1 ... and also, you don't need 60/20s for arches ... 30/10s work just great.

\dmc

I had been told on a few occasions that 60/20 is the way to go with these arches. If 30/10 works fine then that obviously changes the game. Any other input on this?


Reply
Posts: 8
(@jeffcurran)
Active Member
Joined: 12 years ago
11Bravo wrote:I really don't know enough about pixels. But have done some searching on difference between WS2812b pixels and WS2811 pixels. It's all confusing to me. I haven't come across the difference yet. All I have determined is the WS2812b is better than WS2812 and nothing about the WS2811 versus the Ws2812b

I'm planning on doing some 2" HDPE arches also this season. I appreciate some post that say 30pixels/m is a good look and that helps on decision makeing. But about WS2812b and WS2811, I'm still in the woods on.

2812b puts the chip in the LED. So rather than 3 LEDs per ~2" pixel area as with 60/20 2811 strips, there is 1 LED per pixel with 2812b ~every 21/32". Super high resolution at 60 LEDs per meter. Huge RGB channel counts. 180 per meter. I can't imagine a practical application of 2812b for xmas displays viewed from more than 50 feet away.


Reply
Posts: 629
(@dkulp)
Honorable Member
Joined: 14 years ago
navyav8tr wrote:I had been told on a few occasions that 60/20 is the way to go with these arches. If 30/10 works fine then that obviously changes the game. Any other input on this?

I tried some 30/10 in 3/4" pex and didn't really like what it looked like. You could see each "dot" too easily. Maybe with larger diameter PEX it would have diffused better, but with the 3/4 inch stuff, it was too noticeable. I ended up going in the middle with 48/16 strip.


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago
jeffcurran wrote:2812b puts the chip in the LED. So rather than 3 LEDs per ~2" pixel area as with 60/20 2811 strips, there is 1 LED per pixel with 2812b ~every 21/32". Super high resolution at 60 LEDs per meter. Huge RGB channel counts. 180 per meter. I can't imagine a practical application of 2812b for xmas displays viewed from more than 50 feet away.

Thank you for the explanation.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

Arches- With incandescent lights we typically had 7 or 8 sections per arch, 30/10 gives you 10 sections per meter, 60/20 gives you 20 sections per meter, 2811 30/30 gives you 30 sections per meter, 2812b with 60 per meter will give you 60 sections per meter. Even though 30/10 is more than incandescents it doesn't look very good IMHO, even 60/20 isn't great. 30/30 (2811 5v) looks good and I'm sure 2812b would look great, but might cost more than the improvement is worth.


Reply
Page 2 / 2
Share: