try cluster 2 and set the output color order to what you see on test patter 1 , 2 , 3 .
if it is set to rgb and you are seeing Brg , this is the tru color order regardless of ic .
Ray sends out all sorts of color combinations. Change your color order in that drop down menu until clusters 2,3, and 4 test the same as cluster 1. The same chip can be wired many different ways. Keep changing the color order until all your clusters are showing up red test 1 green test 2 blue test 3 and that will solve all of your problems. Your sequencer will output RGB and the board will take of putting the right colors to the right led's. I've run into this problem a lot and this is the easiest way to fix it.
John
as i said the e682 shows you the true color order , you do not need to guess or try other settings . test 1 , 2 , 3 will reveal the true color order .
angus40 wrote:as i said the e682 shows you the true color order , you do not need to guess or try other settings . test 1 , 2 , 3 will reveal the true color order .
I know that is what it does but that is not what is happening when I watch my lights, I do think it has something to do with how my universes are set up.
angus40 called it out - - do test pattern 1 and it should be RED, pattern 2 should be GREEN and pattern 3 should be BLUE. If it's not you need to change the RGB setting to BRG or whatever it takes until it works that way. That way from outside the controller (i.e. your sequencer) will always see things as RGB.
Traneman wrote:I know that is what it does but that is not what is happening when I watch my lights, I do think it has something to do with how my universes are set up.
Step back, take a deep breath, and follow the instructions these guys have provided. Your problem will be solved quicker.
to isolate universe issues set clusters 1-1 through 2-2 pixel lengths to 170 this will treat 1-1 as a universe and 1-2 as a universe ect .
Ultimately you will want to do as Brian suggested and assign an ip and switch t0 unicast to unharness the full potential of your hardware !
best of luck with your learning relations and familiarity of the e682 🙂
Definitely need to sort out where the issue is, have had the RGB order out before, especially on strips compared to bullets. As everyone said, run the E682 test, 1 then 2 then 3, I always write down the first letter of the color that comes up and I always do it while I have them set to RGB. Then if it it BRG, GRB, RBG, etc I know what it in fact is compared to the standard RGB.
Once you have that aligned then I will try a few tests with the sequencer, color wash Red, Green, Blue to be sure it is good. It is possible to mis-address things as well, off by 1 or 2 channels will do it as well, BUT you need to know where everything else is before you jump into that one! I generally make a map in excel then lay my models out in there to double check things. In Xlights you can also validate things using the test section there, turn on specific channels to see where they are and the color that is associates to as well.
That is what I really > Really like about HLS in . Native HLS outputs rgb and combined with the e68x controller having the rgb setting set to rgb , there is no guess work or having channel adjustment issues etc .
Just straight forward logic which streamlines diagnostic issues which increases life expectancy within this hobby 🙂 by reducing frustration and stress causing intense pain, profuse sweating, difficulty breathing , violent ... wait that is something else i was thinking of ... Haloween maybe !
lol
cheers
I believe his configuration is on my advice from another thread. This is not an issue of overlapping universes. That's a perfectly valid configuration. He has it overlapping because his strings are of different lengths. His last string doesn't use the full channel range.
The configuration he is using is the most efficient channel plan for his setup. It minimizes the amount of unused channels keeping extraneous data packets down, and making vixen work most efficiently.
This also is completely unrelated to unicast/multicast. He would have enough universes to do it either way. Multicast eliminates IP addressing and is easier for beginners.
The test patterns in the 68x series boards simply fill the channel buffer with data and ignore any data coming in from the network.
The test patterns are the key here. Run the internal patterns one color at a time. It is a very high possibility that some strings are just built in a different color order than others. Swap the misbehaving strings to the cluster you think is working right. See if the problem follows the string or the port on the board.
--Jon Chuchla--
Sent from my iPhone using Tapatalk
